Bridgeview BALE KING 5300 Series Скачать руководство пользователя страница 9

Страница: 9 / 105

Bridgeview Manufacturing Inc.

FEATURES & OPERATION

Power Take-off

The Bale King bale processor has a PTO shaft which is splined on both ends. The

implement end uses a 1-3/4"-20 spline

with wedge lock bolts. Install onto the gearbox and tighten

the wedge bolts. The bolts should be torqued to

160 ft-lb

and re-torqued after 8 hrs of use.

The tractor end comes standard with a 1-3/8"-21 spline quick detach constant velocity joint.

An optional 1-3/4"-20 spline yoke is available through your Bale King dealer.

The Bale King processor is designed to use a minimum of

100 HP

. The drive shaft is

shear-bolt protected. The machine must be operated at

1000 PTO RPM.

NOTE: Spread yokes and twisted drive shafts are signs of OVERLOAD, not a manufacturer’s

defect and therefore not covered by warranty.

•

DO NOT

operate the machine using a spline adaptor. Use of adaptors will

void warranty

due to damage caused to the tractor PTO, PTO driveshaft, or implement.

•

DO NOT

operate at 540 rpm, or use any kind of adaptor to connect to a 540 rpm spline.

•

Always

ensure that the PTO shaft is attached securely to the tractor. When the processor

is not hooked to the tractor, store the shaft on the PTO holder.

•

DO NOT

transport the processor without securing the PTO shaft. See next page for

securing instruction.

•

Always

ensure that the drawbar is adjusted to

16”

from the end of the tractor PTO shaft to

the center of the hole in the drawbar.

Operation

To engage the rotor for processing a bale, be sure the PTO shaft is properly connected to the tractor.

Engage the PTO at idle. After the PTO is fully engaged, increase PTO speed until it reaches 1000

RPM

The processor must not run at any speed less than 1000 PTO RPM as it may result in the

flails springing back against the rotor after they come in contact with the bale. This “

backslap

”

Содержание BALE KING 5300 Series










































































































Результаты поиска

Содержание BALE KING 5300 Series

Отзывы:

Похожие инструкции для BALE KING 5300 Series

Бренды по названию

Популярные бренды

Bridgeview BALE KING 5300 Series, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание BALE KING 5300 Series

Отзывы:

Похожие инструкции для BALE KING 5300 Series

Бренды по названию

Популярные бренды