background image

 

 

Display location and mounting options 

Your display can be mounted using the flush mounting clamps supplied. Green Marine
recommends that you power up and test the display prior to installation.

When planning the display location, the following points should be considered to ensure 
safe, comfortable, and reliable operation:

 

Power connections 

The power connection to the display should be made at either the output of the battery 
isolator switch, or at a DC power distribution panel. Green Marine recommends that power is 
fed directly to the display via its own dedicated cable system and MUST be protected by 
a thermal circuit breaker or fuse fitted close to the power connection. If you do not 
have a thermal circuit breaker or fuse in your power circuit, you MUST fit an in-line 
breaker or fuse to the positive (red) lead of the power cable. 
 

 

• 

Installation angle

- the MT Series 50 display should be mounted at  an angle. Mounting it 

in a flat plane is not recommended due to increased heat absorption. 

• 

Viewing angle 

- this LCD has been chosen to give the very best performance, including 

viewing angle. However, the contrast and colors seen on all LCD displays vary slightly 
with viewing angle. 

• 

Environment

- to prevent overheating, do not restrict airflow at the rear of the 

display. If the space behind the display is air conditioned or cooled by a fan, it will help in 
keeping the displays temperature down when mounted in direct sunlight. 
FAILURE TO ADEQUATELY VENTILATE THE UNIT COULD INVALIDATE YOUR WARRANTY. 
The display should be protected from physical  damage and excessive vibration. Although 
the display is waterproof from the front when installed correctly, it is good practice 
to mount it in a protected area away from prolonged and direct exposure to rain and salt 
spray. DO NOT mount the monitor near a heat source.

Power connector

Grounding screw

 angle for satisfactory 

should be connected 

 

 Before the display is mounted, power and signal source 

and the display should be held at approximate mounting location to check viewing

picture quality.

13

Содержание BC-MT-1950


































Отзывы: