Brevi 536, Инструкция по эксплуатации, Страница: 22 / 28

22
II. Fitting Instructions
AXO Isofix has been classified in the SEMI-UNI -
VERSAL category and can be installed in two dif-
ferent methods:
Method A: For vehicles equipped with Isofix an -
chor points (cf. list “A” compatible vehicles).
Method B:
For vehicles equipped with three-point
safety belt (cf. list “B” compatible vehicles).
1. This child restraint is classfied for “Semi-
Universal” use and is suitable for fixing into the
seat positions of the following cars:
CAR FRONT
REAR
Outer Centre
BMW series1, 2, 3, 5, 7,
X1, X3, X4, X5, X6...
Mercedes-Benz Class A,
B, C, E, S, G, M ...
Audi A1, A3, A4/A4L, A5,
A6/A6L, Q3, Q5, Q7…
VolksWagen Polo,
Golf, Passat, Tiguan,
Lavida, Sagitar, Magotan,
Phaeton...
Toyota Levin, Corolla,
Camry, Reiz, Crown,
Highlander, Prado...
... ...
No Yes No
2. Seat positions in other cars may also be su-
itable to accept this child restraint, please see
the AXO Isofix list of compatible vehicles.
3. If in doubt, consult either the child restraint
manufacturer or the retailer.
Semi- ersal installation notice: Before install
the AXO Isofix into the car, please read the car
manufacturer’s handbook about ISOfix ancho -
rages information
Method A: Installing the car seat using
the Iso-fix connectors
1. Rotate the support leg so that it is in an upright
position (Pic. 2).
2. Place the child seat on the appropriate vehicle
seat, facing forward (Pic.37).
3. Ensure the vehicle seat is locked in the most
upright and adjusted to the rearward position.
4. To prepare the child seat installation, press si-
multaneously the two levers, on either side of the
child seat base (Pic.3 - A) and push completely
the support leg release unit (Fig. 3 - B), to extract
the connectors (Fig. 3 - C).
5. AXO Isofix comes with two plastic guides (Pic.1-
U) you can use them, if your vehicle has none, to
guide the Isofix connectors in their proper posi -
tion in correspondence of the seat anchor points
of your car.
6. Line up the two plasic guides with the Isofix con -
necting points (Pic. 4).
7. Make sure that the connection indicators are red
(Pic. 5-A): suggesting that the connectors are re-
ady for engagement. If one or both indicators are
green, press the button (Pic. 5-R).
8. Insert simultaneously the two Isofix connectors
through the child seat guides, pushing the sup-
port leg articulation (Pic. 5 -B) to lock them in.
Important: You must clearly hear two
distinct “clicks” and both indicators
should be green (Pic.5-C ). Only in
this case the connectors are properly
attached to the anchor points of the
seat.
9. Adjust the height of the force leg by pressing the
pushbutton located at its the back (Pic. 6) and
slide the lower section until it reaches the floor
of the vehicle.
10. Release the button and check that the support
leg is locked in position and its bottom well in
contact with the vehicle’s floor.
11. The force leg is designed to provide stability to
the seat, preventing it from sinking, in the event
of an accident. Firmly push the child seat to make
it adhere to the seat back of the vehicle (Pic. 7).
Important: When adjusting the force
leg, make sure that the base of the
seat (Pic.8) always remains in con-
tact with the seat
536-03-160429-00. istruzioni AXO Isofix ZH-EN_A6 .indd 22 18/05/2016 11.51.59