Bresser BR-S60 RGB, Инструкция по эксплуатации

Страница: 6 / 20

USING V-MOUNT BATTERIES*
(optional)
1. Slide the fully charged batteries* (2 pieces of type NP-F750
or NP-F960) into the battery holder (5) from above so that
the battery clicks into place.
2. To remove, slide the battery out of the holder in the
opposite direction.
TURNING THE LED LIGHT ON
1. Establish the power supply for the device (insert battery or
connect to mains voltage).
2. Press the On/Off button (14) to switch on the device.
3. Press the On/Off button (14) again to switch off the device.
BRIGHTNESS ADJUSTMENT
1. Press the "DIMMER/COLOR" button (15).
2. When the corresponding function light "DIMMER" (28)
lights up brightly, you can adjust the brightness by turning
the adjustment knob (15).
COLOR TEMPERATURE ADJUSTMENT
1. Press the "DIMMER/COLOR" button (15).
2. If the corresponding function light "COLOR" (28) lights
up brightly, you can set the color temperature (32 to 56 /
corresponds to 3200K to 5600 K) by turning the adjustment
knob (15).
ADJUSTING THE RGB COLORS
1. Press the "MODE" button (6).
2. When the corresponding function light "CCT/RGB" (29)
lights up brightly, you can set the desired RGB color (0 to
360) by turning the adjustment knob (15).
SETTING A CHANNEL
1. Press the Channel button (7).
2. The last set channel (0-99) flashes.
3. Set the desired channel (0 to 99) by turning the adjustment
knob (15).
4. Finally, press the Channel button (7) to save the set channel.
REMOTE CONTROL
USING A DMX CONTROLLER*
1. Connect your DMX controller* to the light using a suitable
RJ45 connection cable* via the DMX sockets (8).
2. Turn on the light and the DMX controller*.
2. Press the DMX/2.4G button. The DMX function is activated
when the corresponding indicator lights up. When the DMX
function is activated, the light can only be controlled via the
DMX controller*.
USING THE 2.4G REMOTE CONTROL
1. Press the On/Off button (21) to switch on the device.
2. Long press the power button (21) to turn off the device.
SCROLL THROUGH THE MENU
Press the menu button (23) to scroll through the menu.
Press 1x = Display 10 "Brightness" 10 = 10%
press 2x = display 56 "color temperature" 56 = 5600K
Press 3x = display 01 "channel" 01 = 1
Choosing a channel
1. Press the menu button (23) three times to get to the
channel menu.
2. Press + or – (22/24) to select the desired channel.
3. Press the menu button (23) to confirm your selection.
SWITCH LIGHT ON/OFF
1. By default, the light status of the selected channel is
"OFF".
2. Press the On/Off button (21) to turn on the light.
3. Long press the On/Off button (21) to turn off the light.
ADJUSTING THE BRIGHTNESS
1. By default, the brightness level is 10% when the device
is turned on.
2. Press the + or – button (22/24) to increase or decrease
the brightness.
SETTING THE COLOR TEMPERATURE
1. Press the menu button (23) to select the color temperature
for the current channel.
2. Press + or - button (22/24) to choose the desired color
temperature.
ADJUSTING THE TILT ANGLE
1. Hold the light and slowly loosen the locking screw (3) for
the rocker joint.
2. Bring the light head into the desired position and hand-
tighten the locking screw (3) again.
MOUNTING ON A TRIPOD*
(optional)
1. Loosen the fastening screw (10) for the tripod connection
(11) so far that the opening of the tripod connection is
exposed.
2. Place the light with the opening of the tripod connection on
the spigot adapter* of a tripod* and tighten the fastening
screw.
DISPOSAL
Dispose of the packaging materials by type. Observe the
current legal regulations when disposing of the device!
Information on proper disposal can be obtained from municipal
waste disposal service providers or the Environmental Agency.
Do not dispose of electronic devices in the household waste!
According to the European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment and its transposition into
national law, used electrical equipment must be collected separately
and recycled in an environmentally sound manner.
*not included with the purchase