POWER SUPPLY:
NOTE:
This device cannot be operated by battery and mains power at
the same time! Before commissioning, make sure that only one of the
two power sources is active. If both power sources are active during
commissioning, this can lead to irreparable damage to the device! The
manufacturer accepts no liability for this!
MAINS OPERATION
1. If necessary, switch off the device using the -knob (11) and remove
the battery(ies).
2. Insert the DC hollow plug (16) into the power connection socket
(10) on the device.
3. Insert the C13 plug (17) of the mains cable into the C14 socket (15)
on the mains adapter.
4. Insert the plug of the mains power cable into the wall socket.
5. Switch on the device.
TIP:
As an alternative to mains operation, the device can also be
operated by means of a rechargeable battery
4
(see Chapter
3.2).
3.2 BATTERY OPERATION
NOTE
This function/use requires optional accessories that are not
included in the scope of delivery: rechargeable battery.
1. If necessary, switch off the unit using the -knob (11) and
disconnect it from the mains (pull out the mains plug (16)).
2. Insert the suitable battery4 into the battery holder so that it audibly
clicks into place.
3. Switch on the device.
6. To remove the rechargeable battery4, switch off the device first .
Push the push button for battery fixation completely and remove
the battery from the battery holder at the same time.
TIP:
As an alternative to battery operation, this device can also be
operated using mains voltage (see "Mains voltage"). Chapter
3.1:
4 LIGHT MODE & ADJUSTMENT
1. Press the control dial (13) for approx. 3 seconds to switch between
the continuous light mode and the scene light mode.
2. In continuous light mode, turn the control knob to adjust the light
intensity of the dimmer between 10% and 100%.
3. In scene light mode, briefly press the control dial to switch between
light intensity, scene light mode (turn the dial to switch between F1
to F6) and flash frequency (turn the dial to switch between 1 to 9).
Explanation of the scene light types:
F1: Paparazzi / F2: Fireworks / F3: Defective lamp
F4: Flash / F5: TV / F6: SOS
5 SLEWING THE LED LAMP
1. Hold the LED lamp in one hand and simultaneously loosen the
fixing screw (6) on the yoke arm with the other hand.
2. Swivel the LED lamp to the desired position and tighten the fixing
screw again.
6 MOUNTING THE LED LAMP ON A
STAND
4
NOTE:
This function/use requires optional accessories that are not
included in the scope of delivery: Photo tripod with spigot attachment.
1. Unscrew the fixing screw (3) for the tripod connection until the
opening of the tripod connection is free.
2. Place the lamp with the tripod connection (4) on the spigot
attachment4 of a tripod4 with sufficient load-bearing capacity.
3. Tighten the fixing screw so that the lamp is fixed to the stand
without wobbling.
4
not included
7 MOUNTING OF ACCESSORIES
4
WITH BOWENS CONNECTION
NOTE:
Before mounting accessories on the mounting ring, it is
recommended to swivel the LED light and fix it in position so that the
LED module points upwards.
Only accessories with Bowens connection can be used!
1. Insert the accessory
4
with the existing three "lugs" into the
corresponding recesses on the pickup ring (1).
2. Fix the accessory in the pickup ring by turning it slightly to the right
or left.
3. For disassembly, first turn the accessory back in the pickup ring
and then pull it off.
DISPOSAL
Dispose of the packaging materials by type. Contact your local
waste-disposal service or environmental authority for
information on the proper disposal.
Do not dispose of electronic devices in the household garbage!
According to the European Directive 2002/96/EU on Waste
Electrical and Electronic Equipment and its transposition into
national law, used electrical equipment must be collected separately
and recycled in an environmentally sound manner.
Observe the current legal regulations when disposing of the device!
Information on proper disposal can be obtained from municipal
waste disposal service providers or the Environmental Agency.
9 CLEANING
Before cleaning the device, disconnect it from the power supply
(remove plug or remove batteries)!
Only use a dry cloth to clean the exterior of the device. To avoid
damaging the electronics, do not use any cleaning fluid.
Protect the device from dust and moisture. Store it in the supplied
bag or transportation packaging. The batteries should be removed
from the unit if it has not been used for a long time.
EC DECLARATION OF CONFORMITY
A "Declaration of conformity" in accordance with the applicable
directives and corresponding standards has been prepared by
Bresser GmbH. This can be viewed at any time upon request at www.
bresser.de/download/SL-LED/CE/SL-LED_CE.pdf
UKCA DECLARATION OF CONFORMITY
A "Declaration of conformity" in accordance with the applicable
directives and corresponding standards has been prepared by
Bresser GmbH. This can be viewed at any time upon request at
www.bresser.de/download/SL-LED/UKCA/SL-LED_UKCA.pdf
Содержание BR-80SL
Страница 7: ......
