Fi
t a
n
d u
se
Fit and use
14
15
PIN Static Seat Belt
PIN Static Seat Belt
PIN 2 point occupant lap belt
1.
Connect the female connector, of the lap belt with tongue to the wheelchair
tie-down with the male connector, (Fig. 3A). Connect the female connector, of
the lap belt with buckle to the wheelchair tie-down with male connector, (Fig.
3B).
2. Draw the lap belts around around the occupant and clip the lap belt tongue
into the lap belt buckle, (Fig. 3C), sitting centrally to the occupant. Adjust as
firmly as possible, consistent with user comfort, such that the lap belt sits
low over the front of the pelvis and bears over the bony part of the body, not
wheelchair components.
3. The lap belt anchor points should be positioned to achieve belt angles of 30°
or more to the horizontal and preferably between 45° and 75°
in order to fit
low across the pelvis, reducing the possiblity of the belt loading the abdomen,
(Fig. 2). The pelvic restraint is designed to bear upon the bony structure of the
body and should be worn low across the front of the pelvis with any junctions
between the pelvic and shoulder restraints located near the wearers hips.
Removing the occupant restraint
1.
Disconnect the female connector
point from the male connector
point on the lap buckle, (Fig. 3C).
2. Disconnect the two lap belt
connector points from the
wheelchair restraint, (Fig. 3A & B),
and remove the restraint from the
occupant. Store safely.
Figure 3
B
A
C
CONFIDENTIAL PROPRIETARY INFORMATION
DO NOT COPY WITHOUT PERMISSION OF
MARTOCK, SOMERSET TA12 6EY
1
2
3
4
5
6
A
B
C
D
7
8
E
F
1
6
7
4
5
8
3
2
B
F
A
D
E
C
COLOUR
FINISH SPEC
FINISH
MATERIAL SPEC
MATERIAL
FOR DIMENSIONS NOT SHOWN SEE CAD DATA.
CAD DATA IS BASIC.
DRAWN BY
ISSUE
TITLE
DRAWING No.
SHEET
1 OF 1
A2
DATE
APPROVED BY
DATE
DIMENSIONS ARE IN MILLIMETER
UNSPECIFIED TOLERANCES:
x.xx 0.25
REMOVE ALL
SHARP EDGES
STOCK CODE No.
CONFIDENTIAL PROPRIETARY INFORMATION
DO NOT COPY WITHOUT PERMISSION OF
MARTOCK, SOMERSET TA12 6EY
1
2
3
4
5
6
A
B
C
D
7
8
E
F
1
6
7
4
5
8
3
2
B
F
A
D
E
C
COLOUR
FINISH SPEC
FINISH
MATERIAL SPEC
MATERIAL
FOR DIMENSIONS NOT SHOWN SEE CAD DATA.
CAD DATA IS BASIC.
DRAWN BY
ISSUE
TITLE
DRAWING No.
SHEET
1 OF 1
A2
DATE
APPROVED BY
DATE
DIMENSIONS ARE IN MILLIMETER
UNSPECIFIED TOLERANCES:
x.xx 0.25
REMOVE ALL
SHARP EDGES
STOCK CODE No.
CONFIDENTIAL PROPRIETARY INFORMATION
DO NOT COPY WITHOUT PERMISSION OF
MARTOCK, SOMERSET TA12 6EY
1
2
3
4
5
6
A
B
C
D
7
8
E
F
1
6
7
4
5
8
3
2
B
F
A
D
E
C
COLOUR
FINISH SPEC
FINISH
MATERIAL SPEC
MATERIAL
FOR DIMENSIONS NOT SHOWN SEE CAD DATA.
CAD DATA IS BASIC.
DRAWN BY
ISSUE
TITLE
DRAWING No.
SHEET
1 OF 1
A2
DATE
APPROVED BY
DATE
DIMENSIONS ARE IN MILLIMETER
UNSPECIFIED TOLERANCES:
x.xx 0.25
REMOVE ALL
SHARP EDGES
STOCK CODE No.
CONFIDENTIAL PROPRIETARY INFORMATION
DO NOT COPY WITHOUT PERMISSION OF
MARTOCK, SOMERSET TA12 6EY
1
2
3
4
5
6
A
B
C
D
7
8
E
F
1
6
7
4
5
8
3
2
B
F
A
D
E
C
COLOUR
FINISH SPEC
FINISH
MATERIAL SPEC
MATERIAL
FOR DIMENSIONS NOT SHOWN SEE CAD DATA.
CAD DATA IS BASIC.
DRAWN BY
ISSUE
TITLE
DRAWING No.
SHEET
1 OF 1
A2
DATE
APPROVED BY
DATE
DIMENSIONS ARE IN MILLIMETER
UNSPECIFIED TOLERANCES:
x.xx 0.25
REMOVE ALL
SHARP EDGES
STOCK CODE No.
Wheelchair
reference
plane
45°
75°
30°
SIDE VIEW
REAR VIEW
15°
15°
300mm
(12in)
Preferred Zone
Optional Zone
Figure 2
