Page 57B
Warnings and
Lift Operating
Instructions
Decal 28540
ADA Standee
and Interlock
Decal 19342
Non Lift-Posted Decals
To remove the masking, start
an edge and peel back
slowly
,
at a sharp angle directly over
the top of the decal.
Parking
Courtesy
Requested
Decal
#12375
Actual Size:
3" W. x 4-3/4" T.
Two Courtesy Requested decals
are supplied with all Braun lifts to
be posted on vehicle as desired.
Decals
TM
12375
Fairfield, NJ USA
Oslo, Norway
Clearwater, FL USA
Kitchener, Ontario Can.
Huntington Beach, CA USA
Rocklea, Queensland Aust.
"Providing Access to the World"
International Corporate Hdqrs: P.O. Box 310 Winamac, IN 46996 USA
1-800-THE LIFT (219) 946-6153 FAX: (219) 946-4670
Parking Courtesy
Requested
Actual Size:
2-3/16" W. x 15/16" T.
Circuit Sentry
(100 A.) Label
Decal #18181
Supplied to be posted near the lift
control box mounting location (lift
posted also - see following page).
Clean powder-coated surfaces
(or painted surfaces) with
isopropyl alcohol
before
decal
or antiskid application. Use a
clean cloth or paper towels.
DO NOT
use oily shop rags.
Wipe surface free of residue
with dry portion of cleaning
cloth.
Mask Removal:
Pay close
attention to this mask
removal procedure when
posting die-cut logo decals.
WA
RNING
Read manual before
operating lift. Call
1-800-THE LIFT to
receive operator's
manual. Failure to
do so may result in
serious bodily injury
and/or property
damage. Keep
manual in lift pouch.
25674
Oper
ual
Man
ato
r's
Operators
Manual
Policy
Warning
Decal 25674
Actual Size:
1-1/2" W. x 3-1/4" T.
Posted on the lift
control box as shown.
Replace missing, worn
or illegible decals.
Failure to do so may
result in serious bodily
injury and/or property
damage.
WARNING
The lift is only as safe as the operator.
Lift-posted decals are shown by mounting
location. Part numbers are provided for all
decals. Inspect your lift for any missing,
worn or illegible decals. Call 1-800-THE
LIFT for replacements.
Decal and Antiskid Application Procedure
Decals and Antiskid
OPERATING
INSTRUCTIONS
19342
Standees must
stand at center of platform (fully inside
yellow boundaries), grip handrails and
lower head to clear door jamb header.
Lift Interlocks
vary in type and operation. Interlock
(if equipped) must be operated as
instructed by transit authority.
Read warnings and operate lift as
outlined on LIFT OPERATING
INSTRUCTIONS decal. Lift operating
instructions apply to wheelchair
passengers and standees.
Standee Instructions:
Interlock Instructions:
WARNING
Read manual before
operating lift. Call
1-800-THE LIFT to
receive operator's
manual. Failure to
do so may result in
serious bodily injury
and/or property
damage. Keep
manual in lift pouch.
25674
Oper
ual
Man
ato
r's
WARNING
LIFT OPERATING
INSTRUCTIONS
• Read manual before operating lift.
• Load and unload on level surface
only.
• Engage vehicle parking brake before
operating lift.
• Provide adequate clearance outside
of vehicle to accommodate lift.
• Do not operate lift if you suspect lift
damage, wear or any abnormal
condition.
• Keep operator and bystanders clear
of area in which lift operates.
Whenever a wheelchair passenger
is on the platform, the:
• Passenger must be positioned
fully inside yellow boundaries
• Wheelchair brakes must be locked
• Handrail belt must be latched
• Roll stop(s) must be up
Failure to follow these rules may result
in serious bodily injury and/or property
damage.
Note: Handrail belt must be
latched to operate lift.
OPEN DOOR(S) AND SECURE
TO UNFOLD PLATFORM:
Stand clear and press UNFOLD
switch until platform stops (reaches
floor level).
Note: In event platform does not
unfold, press FOLD switch to
release Lift-Tite™ latches.
TO UNLOAD PASSENGER:
1. Load passenger onto platform and
lock wheelchair brakes.
2. Press DOWN switch until entire
platform reaches ground level and
roll stop unfolds fully.
3. Unlatch handrail belt.
4. Unlock wheelchair brakes and unload
passenger from platform.
TO LOAD PASSENGER:
1. Load passenger onto platform and
lock wheelchair brakes.
2. Latch handrail belt.
3. Press UP switch to fold roll stop
up and raise platform to floor level.
4. Unlock wheelchair brakes and unload
passenger from platform.
TO FOLD PLATFORM:
Press FOLD switch until platform
stops. Release switch.
CLOSE DOOR(S)
28540
U.S. Patents: 5,261,779 5,806,632
6,065,924 6,238,169 Patents Pending
This unit is designed to protect the electrical system on
all Braun hydraulic wheelchair lifts. In the event of failure,
wait 60 seconds. Then turn RESET lever to reset breaker.
18181
Rating: 100 Amps
The Braun
Circuit Sentry
CAUTION!
Turn RESET lever to reset breaker only!
Turning lever at any other time will result in damage.
Supplied with 100 ampere 12 volt
Circuit Sentry #28910KS.
