background image

Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 32494

Lift Operating Instructions

L

N

M

approximately

 2”

P

UP

O

J

I

F

E

D

A

C

B

DOWN

G

H

K

To Open Door(s):

Automatic Door Operator(s):

Press yellow OPEN switch until 

door(s) are 

fully open

.  Release 

switch.

Manual Door(s):

Manually open door(s) 

fully

 and 

secure.

To Unfold Platform (Out):

Press UNFOLD (orange OUT) 

switch (see Photo B) until platform 

stops

(unfolds fully – reaches 

floor level).

See Photos C and D.

Release switch.

To Unload Passenger:

1. Read notes below!

  Load passen-

ger onto platform 

facing outward

and

lock

 wheelchair brakes.

Note:

 Outer barrier 

must

 be UP

and outer barrier latch 

must

 be 

fully engaged 

before

 loading pas-

senger onto platform.

Lower head

to clear vehicle door jamb heade

r.

2.

 Press red DOWN switch until the 

entire

 platform reaches ground 

level (stops) and outer barrier 

unfolds

fully

(see Photos H and I).

Release switch. 

Switch Arm Switch:  Slide knob in 

to DOWN position.  See Photo G.

3.

 Unlock wheelchair brakes and 

unload passenger from platform.

Note:

 Outer barrier 

must

 be 

fully

unfolded

 (ramp position) until the 

entire wheelchair has crossed the 

outer barrier.  See Photos K and L.

To Load Passenger:

1.

 Load passenger onto platform 

fac-

ing outward

 and 

lock wheelchair 

brakes

.

Note:

  Outer barrier 

must

 be 

fully

unfolded

 (ramp position) until the 

entire wheelchair has crossed the 

outer barrier.  See Photos K and L.

2.

 Press red UP switch until platform 

stops (reaches floor level).  Re

-

lease switch.

Switch Arm Switch:  Slide knob out 

to UP position.

Note:

 Outer barrier 

must

 be 

UP and outer barrier latch 

must

be fully engaged 

before

 raising 

platform.  Platform will raise above 

ground level approximately two 

inches

before

 latch engages

 fully

.

Содержание FMVSS No. 403









Отзывы: