Brady BradyJet J4000 Скачать руководство пользователя страница 10

Страница: 10 / 48

BradyJet J4000 User Manual

2 Setup

Unpacking the Printer

Save all packaging materials! These will be needed if you must ship the printer.

What’s in the Box

Make sure the printer box remains in the upright position at all times. Do not lay the box on its side.

1. Lift the printer out of the box and remove the protective plastic bag.
2. Place the printer on a flat, level surface with enough clearance on all sides to accommodate

air flow and to open the cover.

Note:

Do not place the printer near heat sources such as radiators or air ducts, or in a place subject

to direct sun light, excessive dust, mechanical vibration or shock.

3. Remove the following additional items from the box:
•

USB flash drive containing the following:
•

Printer Driver

•

Driver Installation Guide

•

J4000 User Manual

•

J4000 Quick Start Guide

•

Power Adapter

•

Power Cord

•

USB Cable

•

J4000 CMY Ink Tank Cartridge (J40-CMY)

•

J4000 Ink Cartridge Storage Caps (J40-CAP)

•

J4000 ALIGNMENT ROLL,B2595, 4 inches X 20

feet (101.mm x 6.1m)

Registration

www.bradycorp.com/register

and receive free product support and

updates!

CAUTION!

The tear blade in the bottom front of the printer has a sharp edge.

Содержание BradyJet J4000

















































Результаты поиска

Содержание BradyJet J4000

Отзывы:

Похожие инструкции для BradyJet J4000

Бренды по названию

Популярные бренды

Brady BradyJet J4000, Руководство пользователя

Результаты поиска

Содержание BradyJet J4000

Отзывы:

Похожие инструкции для BradyJet J4000

Бренды по названию

Популярные бренды