background image

Installation

 

SS-3N/BIR3/STD, SS-3N/BIR3/WH

Bradley 

• 215-1496 Rev. J; ECN 17-08-026 

9/7/2018 

11

Cleaning and Maintenance for Terreon

®

Material Description:

  Terreon is a densified solid surface material composed of bio based resin and is resistant to chemicals, 

stains, burns and impact. Surface can be easily repaired with everyday cleansers or fine grit abrasives. Because Terreon is a 
unique cast material, its aggregate flow and distribution, and shades of color can vary from product to product creating natural 
characteristics. 

Routine Cleaning:

  For regular cleaning, use mild neutral base cleaners.

Stubborn Stains:

  Remove tough stains with Soft-Scrub

®

 and a green Scotch-Brite

®

 pad or lightly sand in a circular motion with 

240 grit wet/dry sandpaper. The finish can then be renewed with a maroon Scotch-Brite pad.

Scratches:

  Remove scratches with a green Scotch-Brite pad. The finish can then be renewed with a maroon Scotch-Brite pad.

Hard Water Deposits:

  Remove hard water deposits with a mild solution of vinegar and water. Always rinse the unit thoroughly 

after cleaning.

Restoring the surface:

 Use Hope’s

®

 Perfect Countertop to refresh and protect the Terreon Solid Surface material. Dark Terreon 

colors may require additional care and maintenance. For complete instructions on this additional maintenance, visit bradleycorp.com.

Repair Kits:

  Terreon repair kits are available. Contact your Bradley representative or distributor for part numbers and pricing. 

Repair kits are made to order and have a shelf life of 30 days.

NOTICE!  Do not use strong acid or alkaline chemicals and cleaners to clean Terreon. If these chemicals come in 

contact with the surface, wipe them off immediately and rinse with soapy water. Avoid contact with harsh 

chemicals such as paint remover, bleach, acetone, etc.  Avoid contact with hot pans and objects.

Cleaning and Maintenance for Stainless Steel

Material Description:

 Stainless steel is extremely durable, and maintenance is simple and inexpensive. Proper care, particularly 

under corrosive conditions, is essential. Always start with the simplest solution and work your way toward the more complicated.

Routine cleaning:

 Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia. Apply the 

cleaning solution per the manufacturer's instructions and always use a soft cloth or sponge to avoid damaging the finish.

Stubborn Stains:

 To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball

®

 stainless steel 

cleaner or a soft abrasive. Always follow the manufacturer's instructions and apply in the same direction as the polish lines.

NOTICE!  Never use ordinary steel wool or steel brushes on stainless steel. Always use stainless steel wool or 

stainless steel brushes.

Fingerprints and Smears:

 To remove fingerprints or smears use a high quality stainless steel cleaner and polish in accordance 

with the manufacturer's instructions. Many of these products leave a protective coating that helps prevent future smears and 
fingerprints.

Grease and Oil:

 To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in accordance to the 

manufacturer's instructions and in the direction of the polish lines.

Precautions:

 Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents), thiocyanates (pesticides, 

photography chemicals, and some foods), and iodides on stainless steel equipment, especially if acid conditions exist.

NOTICE!  Do not permit salty solutions to evaporate and dry on stainless steel.

The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the actual source 
of the rust in some iron or steel particles which may be touching, but not actually a part of the stainless steel structure.

NOTICE!  Strongly acidic or caustic cleaners may attack the steel causing a reddish film to appear. The use of these 

cleaners should be avoided.

Brand Names

Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement, nor does the 
omission of any brand name cleaner imply inadequacy. Many products named are regional in distribution, and can be found in 
local supermarkets, department and hardware stores, or through your cleaning service. It is emphasized that all products should 
be used in strict accordance with package instructions.

Содержание Express SS-3N/BIR3/WH
















Отзывы: