BT863
INSTALLATION GUIDE
Version1.0
Specifications
Output protocols
Wiegand 26-199bit, RS485 or custom configuration (Model
dependent)
Power requirement
7-18V DC
Current
consumption
79mA (Idle)
250mA (Peak)
Read range
20-40mm (0.8”-1.6”) at 12V DC depends on the type of card
used
Relay Rating
80mA
Operating
temperature
-10’C to +50’C (14’F to 122’F)
Relative humidity
90% max, operating non-condensing
Reader dimensions
190mm(L) x 98mm(W) x 40mm(D) (7.48”x3.86”x1.57”)
Status LED
Green & Red
Audible tone
Internal and external buzzer control
Keypad
3 x 4 Keypad and 4 Function keys, illuminated
Colour finish
Charcoal
IP rating
IP65
Wiring diagram
Note:
•
A shielded cable is recommended to be used. The shield is connected to controller 0V reference
•
Maximum wiegand data cable length: 150 meters (500 feet)
•
Buzzer and LED are low activated.
•
RS485 and Relay are only for optional use.
•
Terminate or insulate all un-used wires
Regulatory Information
C-Tick: This device is C-Tick complied.
CE: The device has passed all relevant tests and obtained CE approval.
FCC: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device
may not cause interference and 2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressively approved by BQT Solutions could void the user’s authority to operate this
equipment.
Information obtained in this document is subject to change without notice.
For further technical information, visit our website at www.bqtsolutions.com or email
Alternatively contact us at one of our global locations
AUSTRALIA & PACIFIC
BQT Solutions (Australia) Pty Limited
Unit 29, 1 Talavera Road
North Ryde, NSW 2113, Australia
Phone: +61 (0)2 8817 2800
Fax: +61 (0)2 8817 2811
Email: [email protected]
EUROPE AND MIDDLE EAST
BQT Solutions (UK) Limited
Regus, Castle Court, 41 London Road
Reigate, RH2 9RJ
United Kingdom
Phone: +44 (0)17 3773 5071
Fax: +44 (0)17 3773 5072
Email: [email protected]
GREATER ASIA
BQT Solutions Singapore Office
Mediapolis
71 Ayer Rajah Crescent #03-03
Singapore 139951
Phone: +65 6220 7970
Fax: +65 6220 7656
Email: [email protected]
Wire connection
Note:
Power to the unit is provided from the listed control unit or from a
separately UL listed 12V DC power-limited, access control power source.
DO NOT supply power during installation.
Wiring methods shall be in accordance with the Electrical wiring regulation
in your country / region.
Check your circuit diagram for the colour coding of the circuit wiring. The
device can be damaged beyond repair if the wiring is connected incorrectly.
This will void the warranty.
1.
Connect the 0V wire to the power 0V line;
Note
: The 0V line of all power supplies must be connected to a common 0V reference
point.
2.
Connect the Wiegand data wires;
3.
Connect the Buzzer and LED wires;
4.
Connect 12V DC wire;
5.
Place unit on the wall (Make sure the wires are not crushed. This will
void the warranty if damage occurs)
6.
Insert and hand tighten the screws;
7.
Check that the unit is level before tightening the screws;
Note
: Excessive tightening of screws may deform the casing, resulting in a damaged
unit. This will void the warranty.
8.
Turn on the 12V DC power to power up the device.
9.
Allow 5 – 10 seconds for the device to finish initialization (depends on
the application). Make sure the unit is functioning correctly according
to the application specification.
External Use
•
Make sure the wire bundle to the device has an IP rating of at least IP65
Handling
•
Handle the device with care. DO NOT damage or drop unit before
installation. This will void the warranty.
•
If the case is damaged, the unit may not be to the specified IP rating.
Replace the unit if the case is damaged.
Maintenance
•
Once installed the device requires no maintenance.
Warranty
Unless specified otherwise, the Company warrants to the Customer that’ BQT Solutions
Branded Products’ (excluding third party products and software) are covered by a
return to base warranty on defects in materials and workmanship affecting normal use
for a period of the Warranty offered under the Standard Terms and Conditions of Sale
from BQT invoice date (‘Standard Warranty’)
This standard warranty does not cover damage, fault, failure or malfunction due to
external causes including; accident, misuse, problems with electrical power, servicing
not authorised by the Company, usage and/or storage and/or installation not in
accordance with Product instructions, failure to perform required preventative
maintenance, normal wear and tear, act of God, fire, flood, war, any violent or similar
occurrence; any attempt by any person other than Company personnel or any person
authorised by the Company to repair or support the Products and problems caused by
use of parts and components not supplied by the Company. The standard warranty
does not cover any items that are in one or more of the following categories: software;
external devices; accessories or parts added to the product after the product has been
shipped from BQT Solutions.
During the warranty, period beginning on the invoice date, the Company will repair or
replace faulty products (at its absolute discretion) returned to its’ factory. The Customer
must prepay shipping and transportation costs and insure the shipment or accept the
risk of loss or damage during such transportation.
The Customer shall be solely responsible for determining suitability for use and the
Company will, in no event, be liable in this respect. This standard warranty is given in
place of all warranties, conditions, terms, undertakings and obligations implied by
statute, common law, trade usage, and course of dealing or otherwise including
warranties or conditions of merchantability, fitness for purpose, satisfactory quality and
/ or compliance with description, all of which are hereby excluded to the fullest extent
permitted by law.
Copyright © 2014 BQT Solutions Limited. BQT Solutions and the BQT solutions logo are registered trademarks of BQT Solutions (Australia) Pty Ltd.
