background image

 

 Rev D 

11 

7  Warranty 

All

 BOWMAN

®

 H

ydraulic Oil Coolers are guaranteed against manufacturing and material defects for a 

period of twelve months from the date of delivery.  

BOWMAN

®

 should be contacted immediately if a unit is received damaged.  No attempt should be 

made to repair a faulty unit as this will invalidate the warranty.  

For full warranty terms, please see the 

BOWMAN

®

 

Conditions of Sale. A copy of which is available on 

request or via download from the website:  

www.ejbowman.co.uk 

8  Spare Parts  

 A comprehensive stock of spare parts is always available.  Details are given in the Hydraulic Oil Coolers 

brochure which can be downloaded from:  

http://www.ejbowman.co.uk/products/HydraulicOilCoolers.htm

  

Please contact our sales department for price and availability or nearest stockist. 

9  CE Marking Documentation 

Heat exchangers are covered by the Pressure Equipment Directive 97/23/EC  which is mandatory for 
all  EU  member  states..    This  manual  is  part  of  the  compliance  and  points  out  all  essential  safety 

requirements to be observed.   

BOWMAN

®

 H

ydraulic Oil Coolers fall within the Sound Engineering Practice category of the Pressure 

Equipment Directive 97/23/EC and as such cannot be CE marked. 

   

 

 

 

 

 

 

 

 

Содержание EC Series













Отзывы: