BOWIE PUMPS Eco-Seal Series Скачать руководство пользователя страница 9

 

ES IOM Rev 1 

-

 5/13/2021

 

 

9

 

NOTICE:

 

 

Check and inspect all components thor-

oughly for damage/wear and replace as 

necessary.

 

 

STORAGE

 

 

Short Term Storage (6 months or less)

 

 

For storage less than 6 months the following steps are strongly advised:

 

 

1.

 

Store pumps indoors.  If this is not possible, then provide adequate protective covering.  

DO NOT 

allow moisture to collect around the pump.

 

2.

 

Remove the drain plugs, if fitted.  Remove any fitted inspection plates to ensure that the pump 
housing is dry.

 

3.

 

See Manufacturer

s Instructions for motor/gearbox/drive instructions for storage procedures.

 

 

Long Term Storage (6 months or more)

 

 

For storage longer than 6 months in addition to following the short term storage steps, the following pro-
cedures should be carried out every 2

-

3 weeks.

 

 

1.

 

Rotate the pump several full revolutions to avoid the gears setting in the housing.

 

2.

 

If corrosion is present, apply light oil to all rotating parts and repeat step 1.

 

PREVENTATIVE MAINTENANCE

 

Failure to set vehicle emergency 

brake and chock wheels before 

performing service can cause 

severe personal injury or prop-

erty damage.

 

Failure to disconnect and lock-

out electrical power or engine 

drive prior to performing ser-

vice can cause personal injury 

or property damage. 

 

Failure to relieve system pres-

sure prior to performing ser-

vice can cause personal injury 

and property damage

 

If pumping hazardous or toxic 

fluids, pump must be flushed 

before service.

 

Содержание Eco-Seal Series














Отзывы: