BOWIE PUMPS Eco-Seal Series Скачать руководство пользователя страница 1

 

ES IOM Rev 1 

-

 5/13/2021

 

 

1

 

These are SAFETY ALERT SYMBOLS.

 

 

When you see these symbols, be alert to 

the potential for personal injury, death or 

major property damage.

 

 

 

Warns of hazards that WILL 
cause serious personal injury, 
death or major property damage.

 

  

 

Warns of hazards that CAN cause 
serious personal injury, death or 
major property damage.

 

  

 

Warns on hazards that CAN 
cause personal injury or property 

 

damage.

 

  

 

NOTICE:

 

Indicates special instructions which are very 

important and must be followed.

 

 

NOTICE:

 

 

Bowie pumps MUST only be installed in 
systems which have been designed by quali-
fied engineering personnel.  The system 
MUST conform to all applicable local and 
national regulations and safety standards.

 

 

This manual is intended to assist in the in-
stallation and operation of the Bowie 

Eco

-

Seal

 Series pumps, and when possible kept 

with the pump.

 

 

Pump service shall be performed by quali-
fied technicians ONLY.  Service shall con-
form to all applicable local and national reg-
ulations and safety standards.

 

 

Thoroughly review this manual, all instruc-
tions and hazard warnings BEFORE perform-
ing any work on the pump.

 

Manuals, parts lists, and 
technical information availa-
ble at:

 

www.bowiepumps.com

 

TABLE OF CONTENTS

 

Section

 

Page

 

  

Pump Data

 

 

Installation

 

  

Operation

  

 

Preventative

 

Maintenance

 

  

Corrective 

 

Maintenance

 

 

Troubleshooting

 

  

Contact 

 

Information

 

 

  

2

 

  

3

 

  

5

 

  

8

 

  

 

10

 

 
 

12

 

  

13

 

E c o

-

S e a l

™  

S E R I E S

 

INSTALLATION, OPERATION AND 

 

MAINTENANCE MANUAL

 

Содержание Eco-Seal Series














Отзывы: