background image

14

DEPTH AND TARGET DISPLAY

(motion modes only)

READING THE DISPLAY

The Liquid Crystal Display (LCD) shows
the PROBABLE identification of the
targeted metal, as well as the PROBABLE
depth of the target, in inches.

The detector will register a repeating,
unchanging target identification when a
buried target has been located and
identified. If, upon repeated passes over
the same spot, the target identification
reads inconsistently, the target is probably
a trash item, or oxidized metal. With
practice, you will learn to unearth only the
repeatable signals.

The segment identifications are highly
accurate, when detecting the objects
described on the label. However, if you
register in a given category for an unknown
buried object, you could be detecting a
metallic object other than the object
described on the label, but with the same
metallic signature. Also, the greater the
distance between the target and the coil,
the less accurate the target identification.

GOLD TARGETS

Gold objects will

register on the left side of the LCD scale.
Gold will register depending upon its
size. The smaller the gold object, the
further to the left it will register.

Gold flakes

will register under Iron-1

Small gold items 

will register under Iron

or 5¢/PT.

Medium-sized gold items 

will register

under PT or S-cap.

Large gold items

will register under S-

cap or Zinc.

SILVER TARGETS:

Silver objects will

register to the right of the scale, under
25¢, 50¢, or $1, depending on the size
of the object. The larger the object, the
farther to the right it will register.

IRON:

Ferrous objects will register on

the far-left side of the target
identification scale. 1, 2, or 3 indicates
the relative size of iron objects. Small
nails, for instance, will usually
illuminate the Iron-1 arrow whereas
large structural ferrous objects will
usually illuminate the Iron-3 arrow.

Objects in this category could be worthless
scrap, or a more valuable iron relic.

5c/PT: 

Nickels and most newer pull-

tabs(those that stay attached to the
can)  will register here.

PT(pull-tabs):

Pull-tabs from older

beverage cans will register here. Few
newer pull-tabs will also register here.
Many gold rings will also register here.

S-CAP:

Older screw caps from glass

bottles will register here. Large gold
rings, like a class ring, could also register
here. Some non-U.S. coins of recent
vintage will also register here.

ZINC:

Newer pennies (post-1982) will

register here. Many non-U.S. coins of
recent vintage will also register here.

Cu10¢:

Dimes and pre-1982 pennies will

register here. Older, pre-1982, pennies
are composed of copper, which has a
metallic signature similar to a dime. Most
copper coins will register here.

Caution:

The target indications are visual

references. Many other types of metal
can fall under any one of these
categories. While the Discovery 3300 will
eliminate or indicate the presence of most
common trash items, it is impossible to
accurately classify ALL buried objects.

DEPTH INDICATOR:

The Depth Indicator is accurate for
coin-sized objects. It indicates the
depth of the target, in inches. Large
and irregularly-shaped objects will
yield less reliable depth readings

When passing over an object, the
depth indicator will light up and stay
illuminated until another object is
scanned. Repeated indication at the
same depth level indicates an accurate
target detector. If the depth indication
varies with each sweep, try sweeping
at different angles; there may be more
than one target present. With practice,
you will learn the difference between
accurate readings, multiple targets, and
highly erratic readings which evidence
trash or irregularly shaped objects.

Содержание DISCOVERY 3300

























Отзывы: