background image

18

Amplifier Troubleshooting Guide

Status LEDs on Amplifier not Lit

Head Unit (Source) Turned “ON”

Verify

Remote turn-on wire from source to amplifier has proper voltage
Power (B+) connections at amplifier, terminal blocks, and battery are secure
Ground (GND) connections at amplifier and vehicle chassis are secure
Battery B+ fuse is OK
Amplifier fuse is OK
B+ at battery and B+ at amplifier have proper voltage

Status LEDs Lit, no Output from Speakers

Speakers in Normal Operating

Condition

Verify

High-level cables from speaker(s) to amplifier are securely connected
RCA cables from amplifier to source are securely connected
Sensitivity adjustment on amplifier is correctly adjusted

Engine Noise from Speaker(s)

Turn source “OFF”
Disconnect RCA cables at amplifier
If noise stops, check equipment & cables leading to amplifier

Verify

RCA cables are of good quality with no breakage to internal shields
RCA cables from source to amplifier are not run alongside power

Amplifier Output Distorted

Music not Recorded with Intentional Distortion

Verify

Source output to amplifier is not distorted
Amplifier input sensitivity is correctly adjusted

Amplifier Shuts Down, Red and Green LEDs are Lit

Amplifier is in Thermal

Protection Mode

Verify

Amplifier is mounted with adequate air circulation around vents
Amplifier does not have obstructions blocking back or side panel vents
Amplifier is not mounted under carpet
Speakers meet correct impedance for application (mono or stereo hookup)

Amplifier Does Not Turn “ON”, and Red LED is Lit

Amplifier not Connected to

a Shorted Speaker

Verify

Speaker crossover is not defective 
High-level cables from speaker to amplifier are not shorted

Amplifier Does Not Turn “ON”, and Red LED Lit

Speakers, Crossovers, and

Cable are OK

Amplifier requires service

Содержание GT-42




















Отзывы: