background image

Mounting the Boston Bravo

Identify the Bracket

When removed from its packing material, the Boston Bravo’s mounting bracket is fitted into the back of the speaker.
Remove the tape that is 
temporarily holding the
bracket to the speaker, and
then pull the bracket away
from the back of the speaker.
Determine how the Boston
Bravo is to be mounted to the
wall or ceiling. It can be
mounted either horizontally
or vertically, either on an
open section of wall, or where
two or three room surfaces
meet. Refer to the illustration
here to determine what screw
holes on the Boston Bravo
bracket should be used for
your application.

NOTE:

The large rectangular hole in the middle of the bracket will fit a single gang electrical outlet to route the

speaker wire through a conduit.

4

filler cap
inverted

filler cap removed

self-adhesive
rubber feet
applied

bracket
removed

1

3

/

8

34mm

Horizontal Placement–Angled Up 

Vertical Placement

angle/corner
mounting holes (4)
2 per side

single gang electrical
box mounting holes

speaker-to-bracket
mounting holes (2)
1 per side

single gang
electric outlet
opening

speaker cable run 
holes (2)
on top and bottom

flat mounting holes (4)
2 per side

Using the Boston Bravo on a Flat Surface 

The Boston Bravo can be used on a flat surface, such as a table, shelf or the floor. For horizontal placement that tilts
up at 45º, both corner fillers must be used and the bracket must be removed.  For untilted horizontal placement,
the rear stand must be used 

with the mounting bracket attached

(see “Mount the Speaker to the Bracket” on page

6 and the “Rear Stand Installation Instructions” in the enclosed bag that contains the stand). For vertical applica-
tions, a single corner filler must be used on the end that will sit on the surface and the bracket should be removed.
Invert the corner filler so that the small, circular recess faces outward. Attach one of the supplied self-adhesive rub-
ber feet so that its edge contacts the diameter of the recess. Apply two more feet, each at 1

3

8

-inch

(34mm) 

from the

outer edge of the plastic housing where it meets the grille (as shown below left). Do not apply the feet to the grille
cloth, as they will not adhere well.

corner fillers facing in

bracket
removed

Содержание Bravo









Отзывы: