FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of this device.
This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by
user. This equipment complies with FCC/ IC radiation exposure limits set forth for
an uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that it deemed to comply without
maximum permissive exposure evaluation (MPE). But it is desirable that it should
be installed and operated keeping the radiator at least 20 cm or more away from
person’s body (excluding extremities: hands, wrists, feet and ankles). Alteration
or modifications carried out without appropriate authorization may invalidate the
user’s right to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
□ Relocate or reorient the receiving antenna.
□ Increase the separation between the equipment and receiver.
□ Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
□ Consult the dealer or an experienced radio/TV technician for help.
1- ATV22CB All-Terrain Speaker System
1- Bluetooth Multi-Function Controller
1- Multi-Function Controller Handlebar Mounting Kit
1- Quick Connect Power Extension Adaptor
2- Nylon Mounting Straps and Nylon Zip Ties
1- User Manual Quick Start Guide / Poster
1- Warranty Card
USER MANUAL
QUICK START GUIDE
Thank you for purchasing this
ATV22CB All-Terrain Sound System
Please read through these instructions carefully so you will know how to
operate your model properly.
After you have finished reading the instructions, keep this document in a
safe place for future reference.
INFORMATION TO THE USER
INFORMATION TO THE USER
T
he Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks is under license.
Other trademarks and trade names are those of their respective owners.
CAUTION!!
ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
GETTING TO KNOW YOUR
ATV22CB MULTIFUNCTION CONTROLLER (MFC)
BEFORE YOU START
IMPORTANT SAFETY PRECAUTIONS
■ Do not operate mobile equipment while driving a motorized vehicle – safe driving and
safety consideration of others should always be your highest priority.
■ In the event you should notice smoke, strange noises or odor from this product, or any
other abnormal signs, immediately turn off the power and consult your dealer or the nearest
authorized
BOSS AUDIO
Service Center. Using this product in this condition may result in
permanent damage to the system.
■ Set your volume control at a low setting, then slowly increase the sound until you can
hear it comfortably without distortion, or ear discomfort.
■
BE SURE TO OBSERVE THE FOLLOWING GUIDELINES
:
- Do not turn up the volume so high that you can’t hear what’s around you.
- Use caution or temporarily discontinue use in potentially hazardous situations.
INSTALLATION / MAINTENANCE PRECAUTIONS
WARNING
- Always consult a professional installer
■ Do not attempt to install or service this product by yourself. Installation or servicing of this product
by persons without professional training and experience in electronic equipment and motorized
vehicle accessories may be dangerous and could expose you to the risk of electric shock, injury or
other hazards
■ Refer any repairs to a qualified
BOSS AUDIO SYSTEMS
Service Center
■ The
ATV22CB
can be powered from a vehicles cigarette lighter / auxiliary power port, or hard wired
directly to the battery through an optional relay / accessory switch
■ When wiring directly to the vehicles battery, be sure to disconnect the batteries negative terminal
wire before starting any wiring procedures, it is suggested that an optional fuse and fuse holder (not
included) with minimum rating of
15 Amps
be in line with the positive battery terminal
■ The ground cable length should not exceed 18-inches (See wiring diagram)
■ The
ATV22CB
has a weather resistant design, it should not be submerged in or under water under
any circumstances
■ Use only the installation parts provided with the
ATV22CB
■ Wash with a mild soap or detergent and lukewarm water using a clean sponge or a soft cloth. Rinse
well with clean water.
“Don’ts” - Very Important
■ DON’T clean in hot sun or on very hot days
■ DON’T use abrasive or highly alkaline cleaners on the main body
■ DON’T scrape the main body with razor blades, or other sharp instruments
■ DON’T ever use, gasoline, acetone or carbon tetrachloride
GETTING STARTED
1
2
3
4
5
6
7
8
5
6
7
4
2
3
1
MFC - MULTIFUNCTION CONTROLLER
BLUETOOTH INDICATOR LED - BLUE COLOR
POWER INDICATOR LED - RED COLOR
3.5mm AUX-INPUT
PREVIOUS TRACK / Press and hold for VOL -
PLAY/PAUSE / Press and hold for POWER ON
NEXT TRACK / Press and hold for VOL +
NFC SIMPLE PAIR LOCATION
Tips:
EN
Nyne Cruiser
USB CHARGE
5V 1A
CAUTION!! Using other mounting methods may void this warranty
PAIRING & DISCOVERING A NEW BLUETOOTH CONNECTION
1) Power on the
ATV22CB
by pressing and holding down the
Play/Pause
multifunc-
tion button for 3 seconds, the
2
blue and
3
red LEDs will start to alternately flash,
signalling that the ATV22CB is now ready for Bluetooth pairing.
NOTE:
You have 2 minutes before you must restart this procedure over again.
2) Now that the
ATV22CB
is in pairing mode:
ANDROID users:
a. Go into the
Settings Menu
of your device
b. Enter the
Bluetooth Menu
c.
TURN ON Bluetooth
and press
SCAN
d.
“BOSS AUDIO”
will now be displayed under
AVAILABLE DEVICES
e. If prompted, enter passcode: “
0000
”
iOS users:
a. Go into the
Settings Menu
of your
iOS
device
b. Enter the
Bluetooth Menu
c
. TURN ON Bluetooth
d.
“BOSS AUDIO”
will now be displayed
e. If prompted, enter passcode: “
0000
”
3) If
“BOSS AUDIO”
is not seen, repeat the above steps to refresh the “
Device List”
4) When the connection is successful, you are now ready to stream music from your favorite
media player to the
ATV22CB
To avoid battery exhaustion, be sure to occasionally run the vehicles
engine while using this product. Using this product without running the
engine can drain the
battery.
BLUETOOTH OPERATION
BLUETOOTH / NFC OPERATION
RECONNECTION
1) Power on the
ATV22CB
and your last paired device Bluetooth.
2) The unit will now automatically reconnect
3) If your device was previously paired with the
ATV22CB
, but it wasn’t the last paired
device:
a. Ensure no other devices are currently paired
b. Enter the
Bluetooth Menu
on your device being paired
c.
“BOSS AUDIO”
will display under
AVAILABLE DEVICES
d. Choose
“BOSS AUDIO”
to reconnect
4) If the device is out of range from the
ATV22CB
, it will disconnect automatically:
a. To reconnect once device is back in range, press the
Play/Pause
button once
b. The
ATV22CB
will now reconnect to the device
NFC SIMPLE PAIR
NFC
enabled devices tap within 1/2” of the
BOSS
logo, you will hear a confirmation tone,
your device will now automatically be paired without any further procedures, some
NFC
devices will require several attempts to successfully pair
6
2
3
Tips:
EN
Nyne Cruiser
USB CHARGE
5V 1A
Tips:
EN
Nyne Cruiser
USB CHARGE
5V 1A
MULTIFUNCTION CONTROLLER BLUETOOTH OPERATION
1) Press the
PLAY/PAUSE
once to start playing music or press the
PLAY
button from
your device touch screen
2) To skip songs or advance, press the
NEXT TRACK
button
3) To select the previous song, press the
PREVIOUS TRACK
button
VOLUME CONTROL
4) To raise the volume
Press and Hold
the
VOL +
button 2 ~ 3 seconds
5) To lower the volume
Press and Hold
the
VOL -
button 2 ~ 3 seconds
MULTIFUNCTION CONTROLLER AUX-IN OPERATION
1) Power on the
ATV22CB
by pressing and holding down the
PLAY/PAUSE
multifunction button for 3 seconds
2) Disconnect any paired
Bluetooth
device by turning off
Bluetooth
in your devices
Settings Menu
3) Connect the integrated 3.5mm
AUX-IN
cable located on right side of the MFC to your
devices headphone jack
4) Route the wire back to ATV22CB, strap and secure your device in the supplied soft carry
pouch
VOLUME CONTROL
5) To raise the volume
Press and Hold
the
VOL +
button 2 ~ 3 seconds
6) To lower the volume
Press and Hold
the
VOL -
button 2 ~ 3 seconds
STREAMING MUSIC
Make sure your device Bluetooth volume is set at 75% level before
stowing in to the carry pouch
AUX-INPUT
Make sure your device headphone volume is set at 75% level before
stowing in to the carry pouch
ATV22CB
can play audio from any device
that has a 3.5mm headphone audio jack.
YOUR DEVICE
5
7
6
Tips:
EN
Nyne Cruiser
USB CHARGE
5V 1A
Tips:
EN
Nyne Cruiser
USB CHARGE
5V 1A
MULTI-FUNCTION CONTROLLER MOUNTING
LEFT or RIGHT
FOR ILLUSTRATION PURPOSES
YOUR VEHICLE MAY VARY
FOR ILLUSTRATION PURPOSES
YOUR VEHICLE MAY VARY
RUBBER
SHIM
INSERT
WASHER
LOCK NUT
ALLEN HEAD
BOLT
LOCK NUT
ALLEN HEAD
BOLT
MULTI-FUNCTION
CONTROLLER
UNIT
SNAP
BRACKET
Z-BRACKET
HANDLEBAR
CLAMP
TOOLS NEEDED:
- 12mm Socket, Wrench or Pliers
- 6mm Allen Wrench
BEFORE INSTALLING THIS PRODUCT
When replacing the fuse, be sure to only use a fuse of the rating specified on
this product. To avoid short-circuiting, cover any disconnected leads with insulating
tape. It is especially important to insulate any unused wires, which if left uncovered
may cause a short circuit. When connecting other devices to this product, refer to
the manual for the product to be connected. The black cable is ground, make sure
to connect the ground wire first. Ensure that the ground wire is properly connected
to metal parts of the vehicles body frame or direct to the battery if your vehicle
does not have a grounded chassis frame The ground wire of this units power amp
and a second powered system must be connected to the frame separately with
different screws. If the screw for the ground wire loosens or falls out, it could result
in fire or malfunction.
To avoid potential shorts in the electrical
system, be sure to disconnect the (–) bat-
tery cable before installation. Use this unit
with a 12-Volt battery and negative
grounding only. Failure to do so may result
in a fire or malfunction.
SPEAKER MOUNTING SUGGESTIONS
CAUTION!!
Mounting straps should be
double checked to be sure they are tight
and secure before each use of the
vehicle. The carry pouch is designed to
keep your device safe from debris, make
sure to close the pouch cover securely
before using vehicle.
Tips
:
EN
Nyne
Cruiser
USB CHARGE 5V 1A
BLUETOOTH
®
ENABLED
ALL-TERRAIN SOUND SYSTEM
ATV22CB
USER MANUAL
FEATURING 6.5” MARINE GRADE SPEAKERS
AND 1.5” SOFT DOME TWEETERS
with BUILT-IN HIGH POWERED INTERNAL AMPLIFIER
QUICK START GUIDE
ATV22CB
USER MANUAL
BLUETOOTH
®
ENABLED | ALL-TERRAIN SOUND SYSTEM
PRINTED IN CHINA
VER:1.02 EN
iPod / iPhone are trademarks of Apple Inc. registered in the U.S. and other
countries.
BOSS Audio Systems is not affiliated with Apple Inc.
1014
BOSS Audio Systems
3451 Lunar Court • Oxnard, CA 93030
www.bossaudio.com
| 800.999.1236
Tech Support: www.bossaudio.com/support
BLUETOOTH
• Version: 3.0 w/ EDR
• A2DP
• Range: 33ft (10m)
SPEAKERS
• Dimensions: 6.5” / 165.1mm
• Impedance: 4
Ω
• Magnet: 11oz
• Cone Type: PP CARBON
• Tweeter Size: 1.5” PEI SOFT DOME
AMPLIFIER
• Maximum Output Power: 450 Watts
• Input impedance: 10k
Ω
• Frequency Response: 45Hz-25kHz
SPECIFICATIONS
WIRE DIAGRAM
15A
Fuse and fuse holder
(not included)
Chassis
ground
point
BATTERY
Mini-DIN
Connector
Fuse is located inside the power adaptor
Turn counter clockwise to open
Replace with 10A AGC Fuse type only
INSERT
INSERT
OPTIONAL DIRECT BATTERY WIRING CIRCUIT
RED
BLACK
Chassis
ground
point
QUICK RELEASE
POWER ADAPTOR
(INCLUDED)
MFC
POWER ADAPTOR
10A
Ground wire
Metal frame
Recommended 12 ~ 14ga Wire
(not included)
Align arrows
Normally open switch
(not included)
C
NO
Normally Open
ON/OFF switch
GENERAL
• Operational Power: 12VDC (10-16V allowable)
• MAX Current Draw: 8.7A
• Replacement Fuse: 10A AGC TYPE
• Color: Black / Camouflage
• Weight: 15lbs / 6.8Kg
• Dimensions cm WxHxD: 68.0 x 19.8 x 27.5
• Dimensions Inches WxHxD: 26.75 x 7.80 x 10.82
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Tips:
EN
Nyne
Cruiser
USB CHARG
E
5V 1A
6
5
7
Tips:
EN
Nyne Cruiser
USB CHARGE
5V 1A
Tips:
EN
Nyne
Cruiser
USB CHARG
E
5V 1A
Tips:
EN
Nyne Cruiser
USB CHARGE
5V 1A
Tips:
EN
Nyne
Cruiser
USB CHARG
E
5V 1A
All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by
any means, including photocopying, recording, or other electronic or mechanical methods, without the prior writ-
ten permission of AVA Enterprises Inc.
Copyright © 2014 AVA Enterprises Inc.
ATV85B
a
2 cm
OR
b
NOW WITH
SIMPLE PAIR
2 cm
ATV85B
a
2 cm
OR
b
8
THIS PACKAGE CONTAINS
ATV22CB-UM-POSTER-STYLE-42cm X 58cm-DRAFT.indd 2
8/25/2014 6:48:32 PM