Using the wires provided, complete the audio, and power connections in your
vehicle as shown in the diagram below.
Be sure to locate the transmitter in a location and position within direct line-of-sight
of the location in the vehicle you plan to have passengers wearing headphones.
The wireless headphones use (2) AAA batteries (not included), which are located
in one of the earphone housings.
To replace the batteries, follow the diagrams below. To conserve battery life, please
be sure to turn off the headphones whenever they are not in use, even though they
will turn off after a short period of interrupted IR reception. If you expect the
headphones to be unused for several days, remove and store the batteries.
CONTENTS
HS-IR • HP10 User’s Manual - Contents
HS-IR • HP10 User’s Manual - page 5
HS-IR • HP10 User’s Manual - page 2
General precautions
Safety precautions
HS-IR and HP10 Headphone Controls and Features
HS-IR • HP10 User’s Manual - page 3
Troubleshooting
HS-IR • HP10 User’s Manual - page 8
HS-IR • HP10 User’s Manual - page 7
HS-IR Transmitter Features
HS-IR • HP10 User’s Manual - page 4
HS-IR • HP10 User’s Manual - page 6
Specifications
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
may be present which may result in
electric shock. Refer any repairs to a
qualified service technician.
• Do not attempt to repair a damaged,
broken or faulty power cord. Replace
it with a new one immediately.
• If there is smoke or any peculiar odor
present during use or if there is damage
to any of the component enclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible.
If you experience operation or performance problems with this product, compare your
installation with the electrical wiring diagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
The HP10 is an
additional set of
wireless headphones
for use with
the HS-IR system or
monitors
with wireless infrared audio
transmission capability.
2
General precautions
2
Safety precautions
2
Installation precautions
2
What is included?
3
Headphone controls and features
4
HS-IR features
5
System wiring:
HS-IR transmitter
6
Headphone battery replacement
7
Using HP-10 with a monitor with
built-in IR audio transmitter
8
Troubleshooting
8
Specifications
Congratulations on your purchase
of a
wireless infrared
headphone system.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of listening
pleasure.
Thank you for making
your
choice in car audio and video
entertainment!
page
HS-IR
Wireless Infrared Headphone System
(Two Headphones and Transmitter)
HP-10
Wireless Headphones
(for use with BOSS HS-IR and
BOSS Monitors with Infrared
Audio Transmission)
All specifications subject to change without notice.
Transmission system
Carrier frequency
Modulation
Mode
S/N ratio
Channel separation
Distortion
Frequency response
Power source, headphones
Current consumption, headphones
MODEL
IR SENSORS
1
VOLUME CONTROL KNOB
2
SYMPTOM
CAUSE
REMEDY
POWER ON/OFF SWITCH
This button turns the headphone on
and off.
In addition, if headphones do not
receive any infrared audio signal after
a short period of time, they will shut
off automatically to conserve battery
life.
3
6
BATTERY COVER
See the section of this manual about
battery replacement for more details.
4
POWER LED
5
HS-IR
Wireless Headphones with IR Audio Transmitter
2
6
3
4
1
5
Lift battery door release latch.
Lift and remove battery door.
Insert two AAA type batteries (not
included). Be sure to note proper
polarity when installing the batteries.
