Installation
Push-To-Talk
Press the icon button (VOL knob) to access to smartphone voice
assistant capability via Bluetooth.
Adjust Menu Options (SEL)
• Press and hold the
SEL
button (volume knob) to enter into setting menu,
then press the
SEL
button (volume knob) repeatedly to select setting items:
- Clock Display/Settings: Press and hold the
SEL
button (volume knob) to
diplay clock time.
Press and hold the
SEL
button (volume knob) again, the hours digits start
flashing on the display, Set hours by rotating the
VOL
knob.
Short press the
SEL
button (volume knob), the minute digits start flashing.
Set minutes by rotating the
VOL
knob.
- ILL MID/HI/LOW: This receiver is equipped with 3 brightness settings.
Rotate the volume knob to preset the illumination to middle, high or low.
- BASS/TREBLE:-7, -6, ~, 1, 0, +1,~, +6, +7
Note:
BASS and TREBLE settings are only enabled when EQ setting is turned OFF.
- BALANCE:L7, L6,~, L1, 0, R1,~,R6, R7
- FADER:R7, R6, ~, R1, 0, F1, ~ ,F6, F7
- Loudness: LOUD ON/OFF
- EQ(Equalizer) Setting: OFF, FLAT, CLASSIC, POP, ROCK, JAZZ
- Stereo/Mono: Switches between MONO and STEREO reception mode
for radio frequencies.
- DX/LOCAL: Enables or disables the local broadcast mode (LOCAL).
- CLOCK 12/24: Select between 12 hours and 24 hours display.
- AREA US/EU: This car radio is equipped the USA / Europe frequency.
Rotate the volume knob to switch between USA and Europe frequency.
The system will change the frequency setting in about 3 seconds.
• Rotate the
VOL
knob to change values.
Mute On/Off
During AUX mode, briefly press the button to toggle mute on or off.
USB Port
Connect to a USB storage device for audio play, or charging of a mobile
phone.
Hands-free Microphone
To receive your voice when you calling by using this bluetooth handsfree
system.
Aux Audio Input Jack
Connect to the headphone jack on an external device (e.g. a mobile phone
or MP3 player) for audio play.
Connect all wiring harness and slide the head unit into the
mounting
sleeve until it clicks into place.
Turn Unit on/off, Change the Source
• Press any button to turn on the unit. Press and hold the
SRC/PWR
button
to turn off the unit.
•
Press the
SRC/PWR
button to select the different modes: Radio, USB(with
USB device inserted), AUX-IN(aux audio input) and BT(Bluetooth) modes.
Adjust the volume (VOL)
VOL
knob to increase or decrease the volume level.
- Only support speakers of 4 ohms or above.
- +12V DC Negative Ground.
- The maximum current of the Amp remote trigger is 200mA.
!
Wiring Connections
Overview of the Components
General Operation
General Operation
General Operation
Radio Operation
Switch Between USA area and Europe area Frequency
In radio mode, press and hold the
SEL
button (volume knob) to enter into
setting menu, then press the
SEL
button (volume knob) repeatedly to access
the state of the USA and Europe frequency, then rotate the volume knob to
switch between USA and europe frequency. The system will change the
frequency setting in about 3 seconds.
Change Bands
In radio mode, shortly press the
BAND
button to switch between the FM1
(F1), FM2(F2), FM3(F3) and AM1(A1), AM2(A2) bands.
To Store / Recall Preset Stations
The radio can be stored 6 preset stations for each band (FM1, FM2, FM3,
AM1 and AM2) for a total of 30 preset stations.
- To memorize a station:
Press and hold the desired preset buttons (1-6) to save a radio station.
- To recall a preset station:
Briefly press the respective station button (1-6) to recall the corresponding
preset station.
Manual Tuning
In the radio mode:
Press and hold the or button to enter the manual tuning mode.
In manual tuning mode, briefly press the or button to search the next
or previous frequency step by step.
Seek Tuning
In radio mode, press the or button, the automatic search will start, it
will search upward or downward for the strong signal radio station within the
current band. The auto searching will stop until find a station.
Automatic Store Station / preset station scan
Press and hold the
AMS
button to store 18 FM stations and 12 AM stations
automatically.
ANT
F-R
R-R
F-L
R-L
10
Radio Antenna
White
Front Left
Speaker
Rear Left
Speaker
Front Right
Speaker
Rear Right
Speaker
White/Black
ACC + (Red)
GND - (Black)
ANT + (Blue)
Power B+ (Yellow)
Gray/Black
Purple
Purple/Black
Green
Green/Black
Gray
Red: Front Right PRE-AMP Output
White: Front Left PRE-AMP Output
White: Rear Left PRE-AMP Output
Red: Rear Right PRE-AMP Output
Installation
Installation Procedures
First complete the electrical connections and then check for correctness of
connection.
Insert the mounting sleeve into the dashboard. Then bend the tabs
on the mounting sleeve with a screwdriver to achieve fastening of
the mounting sleeve.
Make sure that lock lever is flush with the mounting sleeve( not
projecting outward)
.
Installation Opening
This unit can be installed in any dashboard which has an opening as shown
below.
2.05 inches
7.20 inches
Bracket key
Mounting sleeve
Bracket key
Plastic trim out
1. PWR(power On/Off),
SRC (source) button,
(end call) button
2. VO
L (volume) knob,
(Push-To-Talk) button,
SE
L (select/menu) button
3.
(tune/seek down, previous track, fast reverse) button
4.
(tune/ seek up, next track, fast forward) button
5. BAND button, AMS(automatic store / preset station scan, automatic music
search) button,
(answer call)
6. LCD
Display
7.
(pause/play), (MUTE) button, Preset station 1 button
8.
IN
T
(intro), Preset station
2 button
9. RP
T
(repeat), Preset station
3 button
10. RDM (random)
, Preset station
4 button
11. -10(previous 10 tracks), F-(previous folder), Preset station
5 button
12. +10(next 10 tracks), F+(next folder), Preset station 6 button
13.
IR remote sensor
14. USB Port
15. Hands-free Microphone
16. AUX IN (aux audio input) jack
17.
Reset button
FLAT
CLASSIC
POP ROCK
USB BT
INT RPT RDM
14
16
17
15
Reset
Push the
RESET
button with a thin object with a pointed end to reset the unit.
This function may be used when the LCD does not display normally or
sound is distorted, or when any of controls are disabled.
