background image

 

Safety Instructions 

The safety recommendations outlined in this section are to be read, 
understood and followed before operating the product. Keep this 
information in a safe place for future reference. Failure to comply with any 
of the following safety procedures could result in serious damage. 

„

 

Do not operate product for any purposes other than its intended use 

„

 

This product is intended for indoor use only 

„

 

Do not operate product if power cord is damaged in anyway 

„

 

Do not insert objects into openings 

„

 

Do not immerse product in water or permit liquids to spill inside 

„

 

Turn off power when unattended or not in use. Unplug product before 

moving it or when it is not in use for an extended period of time. The 
socket-outlet shall be installed near the equipment and shall be easily 

accessible 

„

 

Do not alter or extend electric plug. Plug is configured for appropriate 

electrical supply 

„

 

Do not overload electrical outlets beyond their capacity as this can result in a 
fire 

NOTE: 

DO NOT TOUCH THE PRODUCT OR ANY OTHER SENSITIVE 

COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC 

PROTECTIONS. 

Содержание BPF-3012



























Отзывы: