background image

8

Installation

– Scope of delivery: dryer, installation and operating instructions, basket for woollens 

(depending on the model).

– Check dryer for transport damage.
– The dryer is very heavy. Do not attempt to lift it on your own.
– Be careful to avoid sharp edges.
– Do not set up in a room that is susceptible to frost. Freezing water may cause damage. 
– If in doubt, have the appliance connected by a specialist.
– Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.

Setting up the dryer

– The appliance plug must always be accessible.
– Ensure that the appliance is installed on a clean, level 

and firm surface.

– Do not obstruct the air inlet on the front of the 

dryer.

– Keep the area around the dryer clean.
– Make the dryer level using the threaded feet

and a spirit level.

– Do not remove the threaded feet under any 

circumstances.

Mains connection 

see Safety instructions 

a

 page 13.

– Connect to an AC earthed socket. If in doubt have the socket checked by a specialist.
– The mains voltage and the voltage shown on the rating plate (

a

 

page 10

) must be the 

same.

– The connected load and necessary fuse protection are specified on the rating plate.

Frost protection

Preparation

1. Empty the condensate container 

a

 

page 4

.

2. Select any programme using the programme selector.
3. Press the 

(Start)

 button 

a

 condensed water is pumped into the container

4. Wait 5 minutes and then empty the condensate container again.
5. Turn the programme selector to 

(Off).

Transport

– Prepare the dryer 

a

 see Frost protection.

– Transport the dryer in a vertical upright position.
– Following transportation, do not use the dryer for two hours.

The dryer contains residual water; this can flow out if the dryer is tilted.

1.

Take all accessory parts out 
of the drum.
The drum must be empty.

Make sure that the air inlet 
remains unobstructed

Clean and level

Do not set up the dryer behind a door or sliding 
door, as this may obstruct the dryer door or prevent 
it from opening. This will prevent a potentially fatal 
danger to children from locking themselves in.

2.

Do not operate the dryer if 
there is a danger of frost.

9

Care and cleaning

Heat exchanger

The dryer's heat exchanger is cleaned automatically during drying. 

Cln

 appears in the display 

panel. Do not pull out the condensate container during the cleaning process.

Dryer housing, control panel, air intake

Remove detergent residues immediately.
Wipe with a soft, damp cloth.
Do not use harsh cleaning agents or solvents.

Filter in the condensate container

The filter is cleaned automatically when the condensate container is emptied.
However, the filter should still be cleaned regularly under running water 

a

 This prevents 

stubborn deposits/dirt from building up.

1.

Pull out the condensate container.

2.

Pull the filter out of its snap-in lock.

3.

Clean the filter under running water or in the dishwasher.

4.

Refit the filter.

5.

Insert the condensate container so that it locks into place.

Only operate the dryer with the filter inserted.

Moisture sensor

The dryer is equipped with stainless steel moisture sensors. Moisture sensors measure 
how damp the laundry is. A thin layer of limescale may build up on the moisture sensors 
after prolonged use.

1.

Open the door.

2.

Clean the moisture sensors using a damp sponge with a rough surface.

Do not use steel wool or abrasive materials.

Appliance must be switched off.

10

Consumption values table

Programme

Spin speed which 

is used for spinning 

the laundry

Duration**

Energy consumption**

L

Cottons

7 kg

3.5 kg

7 kg

3.5 kg

+

Cupboard Dry*

1400 rpm 

151 min

93 min

1.33 kWh

0.80 kWh

1000 rpm

178 min

110 min

1.65 kWh

0.97 kWh

800 rpm

205 min

127 min

1.92 kWh

1.13 kWh

|

Iron Dry*

1400 rpm

110 min

  71 min

0.94 kWh

0.61 kWh

1000 rpm

137 min

88 min

1.24 kWh

0.80 kWh

800 rpm

166 min

111 min

1.55 kWh

1.04 kWh

I

Easy-Care

3.5 kg

3.5 kg

+

Cupboard Dry*

800 rpm

64 min

0.54 kWh

600 rpm

78 min

0.68 kWh

*

Programme setting for testing in accordance with the applicable EN61121 standard.

**

The values may differ from those specified, depending on the type of fabric, composition of laundry to be dried, residual moisture in the fabric, 
the degree of dryness that has been set, the amount of laundry being loaded and the environmental conditions.

Most efficient programme for cotton fabrics

The following "standard cottons programme" (identified with 



) is suitable for drying normal, wet cotton laundry and is most efficient in terms of 

its combined energy consumption for drying wet cotton laundry.

Standard programme for cottons in accordance with current EU regulation 932/2012

Programme

Load

Energy consumption

Programme duration



Cottons Cupboard Dry

7 kg/3.5 kg

1.65 kWh/0.97 kWh

178 min/110 min

Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU.

Optional accessories

  

(order from the after-sales service using the order number, depending on the model)

 

Washer-dryer stack connection set

The dryer can be placed on top of a suitable washing machine with the same width and depth to save space. The dryer 

must be

 

fastened 

to the washing machine using this connection set. WTZ 11400: with pull-out worktop

.

Installation underneath the worktop

Instead of the appliance covering plate, you 

must

 

have a metal cover fitted by a specialist.

Platform

For easier loading and unloading. The basket contained in the drawer can be used to carry the laundry.

Wollens basket

For drying 

individual

 wollen fabrics, sports shoes and soft toys (see separate instructions for “Woollens basket”).

WTZ
20410

WTZ
10290

WMZ
20500

WMZ
20600

Technical Data

ʠ

Dimensions (DxWxH)

60 x 60 x 85 cm (height adjustable)

Weight

approx. 51 kg

Max. capacity

7 kg

Condensate container

4.0 l

Connection voltage

220-240 V

Connected load

max. 800 W

Fuse protection

10 A

Ambient temperature

5 - 35°C

Product number 
Production number

Inside of door

The rating plate can be found on the back of the dryer.

Power consumption when switched off

0.10 W

Power consumption when ready for use (left-on mode)

1.00 W

ʠ

Drum interior light 

(depending on model)

:

 

The drum lights up after the door is opened and after the programme starts, and switches off 

automatically.

 

11

Normal noises

 

During drying, the compressor and the pump generate some noise which is entirely normal.

The compressor in the dryer may occasion-

ally generate a humming noise. The volume 

and pitch of this may vary

depending on the selected 

programmes and the progress of the 

drying.

The compressor in the dryer is ventilated 

from time to time, which creates a whirring 

sound.

The automatic cleaning process causes a 

clicking noise.

The process of pumping the condensation 

into the condensate container generates 

pumping noises.

12

What to do if...

   

If you cannot rectify a fault yourself (e.g. switching off/on), please contact our after-sales service. We will 
always find an appropriate solution and will avoid unnecessary visits by engineers. Trust the expertise of 
the manufacturer and rest assured that the repair will be carried out by trained service technicians using 
original spare parts. The contact details of your local after-sales service can be found in the enclosed after-
sales service directory.
When contacting the after-sales service, please quote the appliance's product number (E no.) and 
production number (FD) (see under the loading door).
Turn the programme selector to 

0 (Off)

 and unplug the mains plug from the socket.

ʠ

The 

(Start)

 indicator lamp does not 

light up.

Mains plug plugged in?
Programme selected?
Check the socket fuse.

ʠ

The display panel light and indicator 
lights 

(depending on model)

 go out 

and the 

(Start)

 indicator light 

flashes.

Energy-saving mode is activated 

a

 see the separate 

Energy-

saving mode

 instructions.

ʠ

The 

n

 

(Container)

 indicator lamp 

and the 

(Start)

 button are flashing.

Empty the condensate container 

a

 

page 4

.

Clean the condensate container filter if necessary 

a

 

page 9

.

Dryer transported? 

a

 Wait 2 hours and start again.

ʠ

The 

(Filter)

 indicator lamp and 

(Start)

 button are flashing.

Rinse the fluff filter under running water 

a

 

page 4

.

ʠ

Cln

 appears in the display panel.

Not an error. Automatic cleaning of the heat exchanger. Do not 
empty the condensate container.

ʠ

Dryer does not start.

(Start)

 button selected?

Door closed?
Ambient temperature greater than 5°C? The optimum ambient 
temperature for drying is between 5 °C and 35 °C. 

ʠ

Water is leaking out.

Make sure the dryer is level.

ʠ

The door opens by itself.

Push the door closed until you hear it click into place.

ʠ

Creasing.

Laundry load exceeded?
Remove articles of clothing immediately after the end of the 
programme, hang up and pull into shape.
Unsuitable programme selected 

a

 page 7.

ʠ

Laundry is not dried correctly or is still 
too damp.

After the end of the programme, warm laundry feels damper than it 
actually is. Spread the laundry out and allow the heat to disperse.
Finely adjust the dryness level – this extends the drying time but 
does not increase the temperature. Your laundry will become drier.
Select a programme with a longer drying time or increase the 
drying level. This does not increase the temperature.
Select a time programme for extended drying of laundry that is still 
damp.
If you have exceeded the maximum load for the programme, the 
laundry may not be dried correctly.
Clean the moisture sensor in the drum. A fine layer of limescale 
may adversely affect the performance of the sensors and your 
washing will not dry properly.
Drying has been interrupted as a result of a power cut, because the 
condensate container is full or because the maximum drying time 
has been exceeded.

ʠ

Drying time too long.

Rinse the fluff filters under running water 

a

 page 4.

Insufficient supply of air 

a

 ensure that air can circulate.

Air inlet possibly blocked 

a

 Clear inlet 

a

 

page 8

.

Ambient temperature higher than 35°C 

a

 ventilate the room.  The 

optimum ambient temperature for drying is between 5 °C and 35 
°C. Outside of this range, the drying time may increase.

ʠ

The humidity in the room increases 
significantly.

Make sure the room is sufficiently ventilated.
Air inlet blocked? 

a

 Keep clear.

ʠ

Power failure.

Remove laundry from the dryer immediately and spread out. This 
allows the heat to dissipate. Be careful as the door, the drum and 
the laundry may be hot.

ʠ

Other intermittent noises and 
vibrations.

Not an error. Normal noises 

a

 

page 11

.

ʠ

Loud humming noise for several 
seconds.

Has the condensate container been properly inserted? 

a

 Push the condensate container all the way in.

Not an error. Normal noises 

a

 

page 11

.

13

Safety instructions

Emergency

– Pull the appliance plug out of the socket immediately or disconnect the fuse.

ONLY use 
the dryer...

– in rooms inside the house.
– to dry fabrics. 

The dryer 
must NEVER...

– be used for purposes other than those described above.
– be modified in terms of its technology or properties.

Hazards

– The dryer must not be used by children or persons who have not been instructed in 

its use.

– Do not leave children unsupervised near the dryer.
– Keep pets away from the dryer.
– Remove all objects from pockets, and lighters in particular 

a

 Risk of explosion!

– Do not lean or sit on the door 

a

 Risk of tipping!

Installation

– Secure loose cables 

a

 Risk of tripping!

– Do not operate a dryer if there is a risk of frost.

Mains 
connection

– Connect the dryer to an AC earthed socket according to specifications, otherwise it 

cannot be guaranteed that the appliance is completely safe.

– The cable cross-section must be sufficient.

– Only use earth-leakage circuit breakers with the following symbol: 
– The appliance plug and socket must be compatible.
– Do not use multiple plugs/connectors and/or extension cables. 
– Do not touch or hold the appliance plug with wet hands 

a

 Risk of electric shock!

– Never pull the appliance plug out of the socket by its cable.
– Do not damage the mains lead 

a

 Risk of electric shock!

Operation

– Only load the drum with laundry.

Check the contents before you switch the dryer on.

– Do not use the dryer if the laundry has been in contact with solvents, oil, wax, grease 

or paint (e.g. hair styling products, nail varnish remover, stain remover, cleaning 
solvent, etc.) 

a

 Risk of fire/explosion!

– The tumble dryer is not to be used if industrial chemicals have been used 

for cleaning.

– Dust (e.g. coal dust, flour) poses a danger: Do not use the dryer

a

Risk of explosion!

– Do not turn off the dryer until the drying process ends, unless the laundry will be 

removed quickly and spread out, so that the heat can dissipate.

– Do not put laundry containing foamed material/rubber in the dryer 

a

 elastic 

material may be destroyed and the dryer be damaged due to possible deformation 
of the foamed material.

– When cleaning the fluff filter, make sure that no foreign material (down or filling 

material) gets into the air duct opening. If necessary, clean the drum beforehand with 
a vacuum cleaner. If foreign material should still get into the air duct 

a

 call the after-

sales service 

a

 Risk of fire/explosion!

– Light things, such as long hair, may be sucked into the air inlet of the dryer 

a

Risk of injury!

– Final part of a tumble dryer cycle occurs without heat (cool down cycle), to ensure 

that the items are left at a temperature that ensures that the items will not be 
damaged.

– Switch off the dryer once the programme has ended.
– The water from condensation is not drinking water and may be contaminated 

with fluff.

Defect

– Do not use the dryer if it is defective or if you suspect that it is.

Repairs must only be carried out by the after-sales service.

– Do not use the dryer if the mains cable is defective. To avoid danger, only have the 

defective mains cable replaced by the after-sales service.

Spare parts

– Only use genuine spare parts and accessories for safety reasons.

Disposal

– Pull out the appliance plug, 

then

 cut off the mains cable from the appliance.

Dispose of at a municipal waste disposal facility.

– The dryer's heat exchanger contains fluorinated greenhouse (R134a) gas 

in a hermetically sealed unit 

a

 dispose of in a proper manner. Capacity: 0.220 kg.

Total GWP: 0.315 tCO

2

.

– Packaging: Keep all packaging out of reach of babies and children 

a

 Risk of suffocation!

– All materials are environmentally sound and can be reused. 

Dispose of in an environmentally-responsible manner.

en

 

Instruction manual

Dryer
WTW84362SN

Содержание WTW84362SN











Отзывы: