LF
LF
LF
LF
LF
LF
LF
1
:
O
$
Â
LF
$
$
u
~
10
Care
Machine housing, control panel
– Wipe with a soft, damp cloth.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
– Immediately remove laundry and cleaning agent residues.
– Do not clean the appliance with a water jet.
Clean the detergent drawer ...
... if it contains detergent or fabric softener residues.
1.
Pull out the drawer up to the stop position, press down the latch on the
insert and remove the drawer completely .
2.
Remove insert: pull insert upwards with finger.
3.
Clean the detergent dispenser and the insert with water and a brush.
4.
Refit the insert and secure in place (the cylinder should fit over the
guide pin).
5.
Insert the detergent drawer.
6.
Leave the detergent drawer open so that residual water can evaporate.
Drum
Leave the washing machine door open after washing so that the drum can dry.
Rust stains – use chlorine–free cleaning agent, not steel wool.
Descaling
No laundry in the machine!
This is not necessary if the detergent is dosed correctly. However, if it is necessary, follow the
instructions of the descaler manufacturer. Suitable descaling products can be purchased
from our website or after-sales service.
a
page 13
Information on the display
Please close the door immediately because of rising water level. In pause
status
and
are displayed alternately.
Door is locked due to safety reasons (water level and/or temperature are too
high); in pause status,
and
are displayed alternately. If you need
to open the door, wait for the temperature to drop or drain the water (e.g. select
Empty
c
>
programme).
Door cannot be locked/unlocked due to high temperature of the door lock.
Wait a moment and try again.
Flashing
(no water supply):
Tap turned on?
Inlet filter blocked ? Clean filter.
a
page 11
Supply hose kinked or blocked ?
On
(low water pressure):
Only information. No influence
on the programme process.
Clean drain pump;
a
page 11
outlet pipe/drainage hose blocked.
other displays
Switch off the appliance, wait 5 seconds and switch it back on.
If the display appears again, call the customer service
a
page 13
– Risk of electric shock!
Pull out the mains plug!
– Risk of explosion! No solvents!
11
Maintenance
Drain pump
– Set the programme selector to
Â
Off
, disconnect the mains plug.
1.
Open and remove the service flap.
2.
Release the drainage hose from the clip.
Remove the sealing plug from the drainage hose, allow the detergent
solution to flow out. Push the sealing cap back in.
3.
Remove the pump cap. Remove foreign objects/loose debris/fluff from
inside and clean the pump. (impeller in the pump must be able to rotate).
4.
Clean any residual lye or fluff from the thread of the pump cap and
pump housing.
5.
Attach the pump cap and screw it on tight until the stop, handle is upright.
Place the drainage hose back in the retainer.
6.
Place the service flap back on and close.
To prevent unused detergent from flowing straight into the drain during
the next wash cycle: pour 1 litre of water into compartment
II
and start
the
Empty
>
programme. Then select and start a new washing
programme with detergent as usual.
Filter in the water inlet hose
Risk of electric shock
Do not immerse the Aqua-Stop safety device in water (it contains an electric valve).
Reduce the water pressure in the supply hose:
1.
Turn off the tap.
2.
Select any programme (except
Spin
/
Empty
>
).
3.
Touch
Start/Pause
$
button and allow the programme to run for approx. 40 seconds.
4.
Set the programme selector to
Â
Off
. Disconnect the mains plug.
Clean the filter:
Standard
Aqua-Stop
Aqua-Secure
1.
Remove the supply hose from the tap.
Clean the filter with a small brush.
or
on standard and Aqua-Secure models:
Remove the hose from the rear, remove the filter
using pliers and clean the filter.
2.
Reconnect the supply hose and check if it is tight.
– Risk of scalding!
Allow detergent solution to cool down!
– Turn off the tap!
ʑ
ʑ
$
a
ʑ
a
a
a
ʑ
$
ʑ
a
ʑ
ʑ
S
a
a
ʑ
ʑ
~
a
ʑ
LF
ʑ
ʑ
a
ʑ
ʑ
ʑ
2
ʑ
Â
a
Â
a
ʑ
a
ʑ
ʑ
Downloaded From WashingMachine-Manual.com Manuals
