Bosch WIW...V0 series Скачать руководство пользователя

Страница: 15 / 56

Positioning and connecting

Safety instructions

Warning

Risk of injury!

■

The washing machine is very heavy.

Be careful when lifting/transporting

the washing machine.

■

When the washing machine is lifted

by its protruding parts (e.g. the

washing machine door), the

components may break off and

cause injuries.

Do not lift the washing machine by

protruding parts.

■

If the hose and mains cables are not

routed properly, there is a risk of

tripping and injury.

Lay hoses and cables in such a way

that there is no risk of tripping.

Caution!

Damage to the appliance

Frozen hoses may rip/burst.

Do not install the washing machine in

areas exposed to frost or outdoors.

Caution!

Water damage

The connection points for the water

supply hose and water drain hose are

under high water pressure. To prevent

leaks and water damage, you must

follow the instructions in this section.

Notes

■

In addition to the safety information

listed here, the local water and

electricity supplier may have special

requirements.

■

If in doubt, have the appliance

connected by a specialist.

Installation surface

Note:

The washing machine be stable

so that it does not move around.

■

The installation surface must be firm

and level.

■

Soft floors/floor coverings are not

suitable.

Installation on a slide sheet

Slide sheets make it easier to push the

appliance into the installation space

between cabinets.
You can order slide sheets from

specialist retailers/our after-sales

service using the spare part no.

66 1827.

Tip:

Moisten the slide sheets with a

mixture of water and washing-up liquid

before pushing the appliance in. Do not

use grease and/or oil to do this.

Содержание WIW...V0 series

























































Результаты поиска

Содержание WIW...V0 series

Отзывы:

Похожие инструкции для WIW...V0 series

Бренды по названию

Популярные бренды

Bosch WIW...V0 series, Инструкция по эксплуатации и руководство по установке

Результаты поиска

Содержание WIW...V0 series

Отзывы:

Похожие инструкции для WIW...V0 series

Бренды по названию

Популярные бренды