background image

Positioning and connecting       

en

35

Only tighten the screw connections 

by hand. If the screw connections 

are tightened too much with a tool 

(pliers), the thread may be 

damaged.

Optimum water pressure in the supply 

network
At least

 100 kPa (1 bar)

Maximum

 1000 kPa (10 bar)

When the tap is open, the water flow is 

at least 8 l/min.
If the water pressure is higher than this, 

a pressure-reducing valve must be 

installed.

Connection

1.

Connect the water supply hose to 

the water tap (¾" = 26.4 mm) and to 

the appliance:

– Model: 

Standard

– Model: 

Aqua

­

Secure

Tip:  

Connect also an external water 

filter between water supply hose and 

tap. The filter filters dirt particles out 

of the water.

Water filter must be cleaned regularly 

to remove contaminants. This will 

prevent blockages. See also 

~

 

separate installation and cleaning 

instruction for water filter.

2.

Open the water tap carefully, 

checking the leak tightness of the 

connection points. The screw 

connection is under mains water 

pressure.

Water outlet

Caution!

Water damage

If the drain hose slips out of the wash 

basin or the connection point during 

draining due to high water pressure, any 

escaping water may cause water 

damage.

Secure the drain hose so that it cannot 

slip out.

Note:  

Do not kink the water drain hose 

or put strain on it lengthways.

You can lay the water drain hose as 

follows:

Outlet in a sink

:

Warning

Risk of scalding!

When you are washing at high 

temperatures, there is a risk of 

scalding if you come into contact 

with hot detergent solution e.g. if hot 

detergent solution is being drained 

into a wash basin. 

Do not reach into the hot detergent 

solution.

Caution!

Damage to the appliance/fabrics

If the end of the drain hose is 

immersed in the drained water, water 

may be sucked back into the 

appliance and may damage the 

appliance/fabrics.

Make sure that: 

– The plug does not block drainage 

from the sink.

– The end of the drain hose is not 

immersed in the drained water.

Содержание WAK20260IN









































Отзывы: