L
F
i
j
S
=
I
i
j
S
=
i
j
S
=
c
i
j
S
=
:
ä
@
>
i
LF
LF
LF
LF
I
c
:
LF
j
c
>
2
>
11
What to do if ...
ʑ
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not dispensed.
–
Start
/Pause not selected?
– Tap not turned on?
– Filter blocked? Clean the filter
–> page 10.
– Supply hose kinked or trapped?
ʑ
Washing machine door
cannot be opened.
– Safety function active. Wait approx. 2 minutes.
– Is Spülstop (Rinse Hold, without final spin) selected?
–> page 3, 4.
ʑ
Programme does not
start.
–
Start
/Pause selected?
– Washing machine door closed?
ʑ
Detergent solution is not
drained.
– Is Spülstop (Rinse Hold, without final spin) selected?
–> page 3, 4.
– Clean the detergent solution pump
–> page 10.
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the
drum.
– Not a fault - water below the visible area.
ʑ
Unsatisfactory spin
result.
Laundry wet/too damp.
– Not a fault - the unbalanced-load detection system has cancelled
the spin cycle because of uneven distribution of the laundry.
Distribute small and large items of laundry evenly inside the
drum.
–
S
Reduced Ironing
selected?
–> page 5.
– Too low a speed selected?
–> page 5
.
ʑ
Spin cycle performed
several times.
– Not a fault - unbalanced load detection system adjusts the
imbalance.
ʑ
Residual water in the
compartment for care
products.
– Not a fault - the action of the care product is not affected.
– Clean the insert if necessary
–> page 9
.
ʑ
Odour formation in the
washing machine.
– Run programme
LF
Cottons 90 °C
without laundry. Use
standard detergent.
ʑ
Foam escaping from the
detergent drawer.
– Too much detergent used?
If foam is escaping from the detergent drawer:
Mix 1 tablespoon of fabric softener with ½ litre of water and pour
into compartment
II
(not with outdoor or down fabrics).
– Reduce the detergent dosage for the next wash cycle.
ʑ
Intense noise formation,
vibrations and “walking”
during the spin cycle.
– Are the appliance feet fixed?
Secure the appliance feet
–> Installation instructions
.
– Transportation safety devices removed?
Remove the transportation safety devices
–> Installation
instructions
.
ʑ
The indicator lights do
not function during
operation.
– Power cut?
– Fuses tripped? Reset/change the fuse.
– If the fault occurs repeatedly, call the after-sales service.
ʑ
Programme sequence
longer than usual.
– Not a fault - unbalanced load detection system adjusts
imbalance by repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional
rinse cycle.
ʑ
Detergent residues on
the laundry.
– Occasionally, phosphate-free detergents contain water-insoluble
residues.
– Select
2
Rinse
/Spin
or brush out the laundry after washing.
If you cannot correct a fault yourself or a repair is required:
– Turn the programme selector to
Off
and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service
–> Installation instructions.
Washing machine
en
Instruction manual
