:
L
F
:
:
:
V
:
I
:
1
:
K
:
:
/
øø
ø
c
:
ä
$
øø
ø
c
:
6
:
2
c
c
>
I
LF
LF
I
I
1
/cc
I
I
$
>
>
$
11
What to do if ...
ʑ
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not dispensed.
– Is
$
Start
/Pause not selected?
– Tap not turned on?
– Filter blocked? Clean the filter
–> page 10.
– Supply hose kinked or trapped?
ʑ
Washing machine door
cannot be opened.
– Safety function active. Wait approx. 2 minutes.
–
c
(without final spin) selected?
–> page 4.
ʑ
Programme does not
start.
–
$
Start/
Pause or
Ready in
selected?
– Washing machine door closed?
ʑ
Detergent solution is not
drained.
– - - - - (without final spin) selected?
–> page 4.
– Clean the detergent solution pump
–> page 10.
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the
drum.
– Not a fault - water below the visible area.
ʑ
Unsatisfactory spin
result.
Laundry wet/too damp.
– Not a fault - the unbalanced-load detection system has cancelled
the spin cycle because of uneven distribution of the laundry.
Distribute small and large items of laundry evenly inside the drum.
– Speed selected too low?
–> page 5
.
ʑ
The programme duration
changes during the wash
cycle.
– Not a fault – the programme sequence is optimised for the
particular wash process. This may result in changes to the
programme duration in the display field.
ʑ
Spin cycle performed
several times.
– Not a fault - unbalanced load detection system adjusts the
imbalance.
ʑ
Residual water in the
compartment for care
products.
– Not a fault - the action of the care product is not affected.
– Clean the insert if necessary
–> page 9
.
ʑ
Odour formation in the
washing machine.
– Run programme
Cottons Stains 90 °C
without laundry. Use
standard detergent.
ʑ
Status display
³
þ
flashes.
Foam may be coming
out of the detergent
drawer.
–
Too much detergent used? Mix 1 tablespoon of fabric softener
with ½ litre of water and pour into dispenser
II
(not for outdoor
and down-filled textiles!).
– Reduce the detergent dosage for the next wash cycle.
ʑ
Intense noise formation,
vibrations and
“wandering” during the
spin cycle.
– Are the appliance feet fixed?
Secure the appliance feet
–> Installation instructions
.
– Transportation safety devices removed?
Remove the transportation safety devices
–> Installation
instructions
.
ʑ
Noises during spin and
drain cycles.
– Clean detergent-solution pump
–> page 10.
ʑ
Display panel/indicator
lamps do not function
during operation.
– Power cut?
– Fuses triggered? Reset/change the fuses.
– If the fault occurs repeatedly, call the after-sales service.
ʑ
Programme sequence
longer than usual.
– Not a fault - unbalanced load detection system adjusts
imbalance by repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional
rinse cycle.
ʑ
Detergent residues on
the laundry.
– Occasionally, phosphate-free detergents contain water-insoluble
residues.
– Select
2
Rinse/Freshen up
or brush the laundry after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to
Off
and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service
–> Installation instructions.
Washing machine
en
Instruction manual
