Bosch UniversalDrill 18V-60 UniversalImpact 18V-60, Оригинальное руководство пользователя

Страница: 16 / 219

16 | English
UniversalDrill 18V-60 UniversalImpact 18V-60
K m/s
2
1.5 1.5
Impact drilling into concrete:
a
h
K
m/s
2
m/s
2
–
–
15
2
Screwdriving:
a
h
K
m/s
2
m/s
2
< 2.5
1.5
< 2.5
1.5
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
Charging the Battery
u
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
Do not continue to press the On/Off switch after the
power tool has automatically switched off.
The battery
can be damaged.
Removing the battery
To remove the battery , press the battery release button and
pull the battery to the rear and out of the power tool.
Do not
use force to do this.
Battery charge indicator
When the on/off switch (11) is pressed in halfway or com-
pletely, the battery charge-control indicator (9) indicates
the charge condition of the battery for several seconds. The
indicator consists of three green LEDs.
LED Capacity
Continuous lighting 3 x green 75–100 %
Continuous lighting 2 x green 40–75 %
Continuous lighting 1 x green 15–40 %
Slowly flashing light 1 x green 0–15 %
The three LEDs in the battery charge indicator flash
quickly when the temperature of the battery is outside
the operating temperature range of –30 to +65 °C and/or
the overload protection has been triggered.
Changing the tool (see figure A)
u
The application tool may heat up significantly during
operation.
Allow it to cool down before touching it.
The drill spindle is locked when the on/off switch (11) is not
pressed. This makes it possible to change the application
tool in the drill chuck quickly, conveniently and easily.
Open the keyless chuck
(2) by turning it in the direction of
rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the keyless chuck (2) by turning it by hand in
the direction of rotation ➋ . This will automatically lock the
drill chuck.
1 609 92A 6RH | (19.10.2021) Bosch Power Tools