Bosch TRONIC 5000C Pro Скачать руководство пользователя страница 4

Страница: 4 / 5

Data subject to change without notice | Printed in the USA | BTC 722002307 A | 01.2014

Bosch Thermotechnology Corp.

4 | Triac Printed Circuit Board Replacement

Reconnecting the wiring

1. Refer to the wiring diagram for each model. Re

tting of the ¼”

connectors (Fig. 2) should be done by pushing them straight
onto the tabs on the printed circuit board. Use a

at blade

screwdriver to push the connectors on if required after aligning
for straight engagement.

2. Assemble the wiring to the printed circuit board nearest the

metalwork

rst for ease of access (Fig. 12 - 16).

Fig. 12

17kW & 27kW

Brown terminal block wire

Left hand assembly– Short Blue element wire
Right hand assembly– Short Black element wire

Left hand assembly – Blue terminal block wire
Right hand assembly– Black terminal block wire

Short Brown
element wire

Fig. 13

27kW only

Short Grey element wire

Grey terminal
block wire

Fig. 13

27kW only

Short Grey element wire

Grey terminal
block wire

Fig. 14

Grey terminal
block wire

Short Grey
element wire

36kW Only

Left hand assembly – Short Blue element wire
Center assembly – Short White element wire
Right hand assembly – Short Black element wire

Left hand assembly – Blue terminal block wire
Center assembly – White terminal block wire
Right hand assembly – Black terminal block wire

Fig. 15

36kW center & left assemblies

Brown terminal block wire

Short Brown element wire

Fig. 16

Brown terminal block wire

36kW right assembly

Short Brown element wire

Содержание TRONIC 5000C Pro






Результаты поиска

Содержание TRONIC 5000C Pro

Отзывы:

Похожие инструкции для TRONIC 5000C Pro

Бренды по названию

Популярные бренды

Bosch TRONIC 5000C Pro, Технический сервисный бюллетень

Результаты поиска

Содержание TRONIC 5000C Pro

Отзывы:

Похожие инструкции для TRONIC 5000C Pro

Бренды по названию

Популярные бренды