Bosch TR6000R 18/21 ESOB, Руководство по эксплуатации

Страница: 7 / 28

Operating instructions
7 6 720 876 031 (2020/06)
Safety of electrical devices for domestic use and
similar purposes
The following requirements apply in accordance with
EN 60335-2-35 in order to prevent hazards from
occurring when using electrical appliances:
“This appliance can be used by children of 3 years and
older, as well as by people with reduced physical,
sensory or mental capabilities or lacking in experience
and knowledge, if they are supervised and have been
given instruction in the safe use of the appliance and
understand the resulting dangers. Children shall not
play with the appliance. Cleaning and user
maintenance must not be performed by children
without supervision.”
“If the power cable is damaged, it must be replaced by
the manufacturer, its customer service department or
a similarly qualified person, so that risks are avoided.”
Congratulations on purchasing this BOSCH appliance.
You have acquired a top-quality product, which will
give you a lot of enjoyment.
2 Operating instructions
2.1 Getting to know your appliance
This appliance is an electronically-regulated, pressurized continuous-
flow heater for decentrally supplying hot water.
The electronic continuous-flow heater heats the water as it flows through
the appliance. One or more taps can be supplied with warm water.
2.2 Operating elements
1 Rotary selector switch
2 Status display
3 Operating the appliance
3.1 Switching the appliance on and off
The continuous-flow heater switches on and heats the water when the
warm water tap is opened. It switches off again if the water tap is closed.
3.2 Setting the water temperature
• Turn the rotary selector switch.
Use the continuously-variable switch to set the desired temperature for.
Note: If a thermostatic-regulating mixer tap is used for high
temperatures or for large water volumes, then it is recommended
that the setting “50 °C” or “60 °C” be selected.
3.3 Solar heated
The appliance can be operated with pre-warmed water (for example,
from a solar energy unit).
WARNING:
Attention!
Scalding danger!
▶ If the output temperature of the water leaving the tap is higher
than the set temperature, then this is because the supply water
temperature from the domestic system is too hot, e. g. due to its
being heated by a solar energy unit.
Increasing the water temperature
If a higher temperature is not obtained when the warm water tap is fully
opened, then this is because more water is flowing than the continuous-
flow heater’s power capacity can heat.
• If this happens, then slightly close the warm water tap.
Decreasing the water temperature
• Turn the rotary selector switch to a lower level e. g. “30 °C”.
Note: If the temperature of the water supplying the appliance changes,
then the output temperature of the water leaving the tap also changes
correspondingly.
3.4 Status display
3.5 Startup after power failure
• Open the warm water tap fully and allow water to flow until it is warm.
3.6 Using the appliance after switching off the water
supply
• Switch off the appliance (unscrew the fuse in the fusebox).
• Open the warm water tap and keep it open until the air has been
completely forced out of the water pipe.
• Switch the fuse back on again.
• Open the warm water tap fully and allow water to flow for at least
one minute.
Only then (for safety reasons) will the appliance begin to heat.
The appliance is now ready to operate.
3.7 Saving energy
• Set the desired water temperature directly on the appliance.
The appliance is operated economically when set to approximately
“40 °C”.
LED Appliance status
Off Off
Lights green On
Flashes green (1/s) The set temperature is not obtained; the rate
of water flow is too high for appliance rating
(the appliance has reached the power limit).
See “ A fault, what to do?”
Flashes green (2/s) Cold-water rinse-through phase
Flashes red See “ A fault, what to do?”