manualshive.com logo in svg

Bosch TDS2510, Инструкции по ремонту

Поделиться
Скачать
Bosch TDS2510 Скачать руководство пользователя страница 2

 
 

204_58300000120957_ARA_EN_E.doc – 29.08.a 

Seite 2 von 37 

1 SAFETY 

1.1 Safety 

precautions 

 

 

Danger! 

Repairs should be carried out by personnel from the manufacturer’s 
own technical department. 
Improper repairs may be harmful to the users. 
The appliance should be disconnected from the mains before being 
dismantled. Inside there are parts that are subjected to high voltage 
levels. 
After being repaired, VDE 0701 tests should be conducted or else the 
specific standard regulations of the country concerned should be 
observed. 
The main electricity cable may only be replaced by personnel from the 
technical department, using spare cable. 
 

1.1.1 

Safety precautions during use 

 

 

Danger! 

Connect and use the appliance only in accordance with the 
information supplied on the iron’s specifications plate.  Do not connect 
the appliance to the power supply in the event of there being visible 
signs of damage to the cord or the appliance itself. Keep the 
appliance beyond the reach of children. 

Only a resilient, steady ironing board should be used. Should the iron 
fall or show signs of not being watertight, it should be examined by the 
Official Technical Department before being used again. 
First unplug the electricity cable from the mains socket before filling 
the tank with water. Disconnect the appliance from the power supply 
after each use or whenever checking for defects. 
So as to avoid potential hazards, repairs and interventions that need 
to be carried out on the appliance like, for instance, replacing the cord, 
should only be performed by qualified personnel from the Official 
Technical Department. 
When leaving the place where the ironing is being done, disconnect 
the iron from the power supply by removing the cable from the mains 
socket. 
 

1.2 Trouble-shooting 

 

 

Warning! 

Never attempt to carry out repairs by means of an indiscriminate 
exchange of component parts. 
Proceed in a systematic way and pay attention to the technical 
documents supplied with the appliance. 
The electronic plates should not be repaired, but replaced with original 
parts from the manufacturer. Exceptions are listed in separate 
documents.  
When conducting checks with the appliance open, avoid contact with  
parts that are hot or subject to tension. 
 

Содержание TDS2510






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды