Bosch Security Systems, Inc.
| 2
Callout ― Description
1 ― Flat surface mounting holes
2 ― Corner surface mounting holes
3 ― Removable bubble level horizontal
4 ― Bubble level holder (swivel mount
only)
5 ― Tamper plate
6 ― Rotary lock
7 ― Battery tray location
8 ― Feature switches
9 ― Look-down adjustment
10 ― Tamper switch
1
3
4
5
6
1
2
8
9
7
10
1
2
2
2
1 | Overview
3 | Installation considerations
4 | Installation
Figure 1.1: Detector base interior view
(top), detector body interior view (bottom)
The RADION PIR ZB is a wireless motion
detector with ZigBee technology that has a
dense zone pattern, and is easy to install.
Point away from:
–
Glass exposed to the outdoors
–
Direct and indirect sunlight
–
Objects that change temperature
rapidly such as heat sources or air
conditioning outlets
–
Outside traffi
c
–
Objects animals might climb on
(stairs, shelves, furniture)
Install:
–
On solid, vibration free surface
–
On a fl at or corner surface
–
Within recommended mounting height
range measured from the fl oor
–
Where an intruder is most likely to
cross through the coverage pattern
Do not install:
–
Near rotating machines or other
moving objects within the coverage
pattern
–
Near objects that can block the fi eld-
of-view
–
Where an intruder would only walk
directly toward or away from the
detector
–
Near direct hot or cold drafts
Pet immunity:
–
Up to 45 lbs (20 kg).
Open the detector and mount the base to
either a fl at surface, a corner, or a bracket.
Opening the detector:
1.
Turn the rotary lock at the bottom of the
detector to the open position. The body
slides down. Refer to
Figure 4.1.
2.
Pull apart to remove it from the base.
Figure 4.1: Unlock and open detector
Mounting the base:
1.
Identify mounting location and surface
for install. (Optional mounting brackets:
B335 and B338. Sold separately).
2.
Identify mounting holes to use based on
the mounting surface. Refer to
Figure 1.1
.
3.
Break away or drill through the
appropriate mounting hole coverings in
the base.
1
NOTICE!
Do not break away or separate the
tamper plate from the base.
Figure 4.2 Surface mount: left; corner
mount: right
Leveling the motion detector:
1.
Position the base on the surface and
mount in place using one screw and
drywall anchor only. Do not over-tighten.
2.
Use the bubble level to ensure the base
is level from side to side. Refer to
Figure
4.3-A.
3.
Remove the bubble level and place it into
the bubble level holder to verify vertical
alignment. This is applicable for swivel
mount brackets only. Refer to
Figure
4.3-B
.
4.
Make adjustments until the base is level,
and mark the remaining surface mounting
hole locations.
5.
Remove the bubble level from the holder
and place it back to its original position.
6.
Secure the base with the remaining
screws and drywall anchors. Use a total
of 3 screws and drywall anchors for
surface mount installations, and 2 screws
and drywall anchors for corner mount
installations.
Figure 4.3: Level detector
5
|
Confi guration
Setting the switches:
1.
Switch 2 - LED illumination. The LED
illuminates when the device detects PIR
activity. By default, the LED is disabled
(switch down). If you do not want the
LED indication after you fi nish the set up
and walk tests, place the switch in the
off position (switch down).
Confi gure the features and options located on
the detector body before placing the detector
body on the base.
5.1 | Set the switches
2
NOTICE!
Use of a bracket might reduce
range and increase dead zone
areas.
NOTICE!
At least one screw must be
inserted into the tamper switch
for tamper protection.
A.
B.
NOTICE!
Supported mounting heights range
from 7.5 ft to 9 ft (2.3 m to 2.7 m).
2 | Product Contents
This poduct contains:
–
Wireless motion detector
–
Installation instructions
–
Hardware pack
–
Battery tray with one battery
You will need a power drill and a fl at-head
screwdriver to perform the installation.
Use a smart phone and scan the following
QR code for more information regarding
installation and mounting considerations.
PRELIMINARY
