manualshive.com logo in svg

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 237 / 282

Поделиться
Скачать
Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 237

15  Accessories

15.1  Optional Accessories

Optional accessory

Type and descriptions

External EMC filter

For detailed information, please refer to 

chapter 15.2  "Ex-

ternal EMC Filter" on page 209

.

Tab.  15-1:   Optional accessories

15.2  External EMC Filter

15.2.1  External EMC Filter Type

VFC 3210 model

External EMC filter type

0K40-1P2

FCAF01.1A-A050-E-0010-N-03-NNNN (0010-N-03)

0K75-1P2
1K50-1P2

FCAF01.1A-A050-E-0020-N-03-NNNN (0020-N-03)

2K20-1P2

FCAF01.1A-A050-E-0025-N-03-NNNN (0025-N-03)

0K40-3P4

FCAF01.1A-A050-E-0008-A-05-NNNN (0008-A-05)

0K75-3P4
1K50-3P4

FCAF01.1A-A050-E-0020-N-05-NNNN (0020-N-05)

2K20-3P4
4K00-3P4

Tab.  15-2:   External EMC filter type

●

Only  mount  the  EMC  filter  FCAF  vertically.  Keep  at  least  80  mm

above the top and below the bottom of the EMC filter free from

mounted parts.

●

For  EMC  performance  with  the  external  EMC  filter,  see 

chapter

6.2.3  "Maximum Length of Motor Cables" on page 25

.

VFC 3210 

Bosch Rexroth AG

Accessories

DOK-RCON04-VFC3210****-IT01-EN-P

209/253

Содержание Rexroth VFC 3210



























































































































































































































































































Отзывы:

Нет отзывов