Bosch Rexroth Tightening System 350, Руководство пользователя

Страница: 483 / 641

3 608 878 300 Tightening Technology | Bosch Rexroth AG 483 /641
System 350 | 3 608 878 300/2019-03
The error codes are output by the IL via the A data (8 bytes as of %QB132). The signals have to be
applied as follows:
Profinet interface – Tightening system inputs (PLC outputs)
The following block (see table 6–161 ) contains general signals for tightening cell control. The following
PLUS communication signals are also included:
• InPos: This signal is set by the station PLC as long as a vehicle is in the station.
• StartReport: Starts transmission of collected results data to PLUS
• ChnErrAck: Set by the PLC to report acceptance of a system error
– KE ILOut 132.0 to A 56.0 – KE ILOut 134.5 to A 58.5 – KE ILOut 137.3 to A 61.3
– KE ILOut 132.1 to A 56.1 – KE ILOut 134.6 to A 58.6 – KE ILOut 137.4 to A 61.4
– KE ILOut 132.2 to A 56.2 – KE ILOut 134.7 to A 58.7 – KE ILOut 137.5 to A 61.5
– KE ILOut 132.3 to A 56.3 – KE ILOut 135.0 to A 59.0 – KE ILOut 137.6 to A 61.6
– KE ILOut 132.4 to A 56.4 – KE ILOut 135.1 to A 59.1 – KE ILOut 137.7 to A 61.7
– KE ILOut 132.5 to A 56.5 – KE ILOut 135.2 to A 59.2 – KE ILOut 138.0 to A 62.0
– KE ILOut 132.6 to A 56.6 – KE ILOut 135.3 to A 59.3 – KE ILOut 138.1 to A 62.1
– KE ILOut 132.7 to A 56.7 – KE ILOut 135.4 to A 59.4 – KE ILOut 138.2 to A 62.2
– KE ILOut 133.0 to A 57.0 – KE ILOut 135.5 to A 59.5 – KE ILOut 138.3 to A 62.3
– KE ILOut 133.1 to A 57.1 – KE ILOut 135.6 to A 59.6 – KE ILOut 138.4 to A 62.4
– KE ILOut 133.2 to A 57.2 – KE ILOut 135.7 to A 59.7 – KE ILOut 138.5 to A 62.5
– KE ILOut 133.3 to A 57.3 – KE ILOut 136.0 to A 60.0 – KE ILOut 138.6 to A 62.6
– KE ILOut 133.4 to A 57.4 – KE ILOut 136.1 to A 60.1 – KE ILOut 138.7 to A 62.7
– KE ILOut 133.5 to A 57.5 – KE ILOut 136.2 to A 60.2 – KE ILOut 139.0 to A 63.0
– KE ILOut 133.6 to A 57.6 – KE ILOut 136.3 to A 60.3 – KE ILOut 139.1 to A 63.1
– KE ILOut 133.7 to A 57.7 – KE ILOut 136.4 to A 60.4 – KE ILOut 139.2 to A 63.2
– KE ILOut 134.0 to A 58.0 – KE ILOut 136.5 to A 60.5 – KE ILOut 139.3 to A 63.3
– KE ILOut 134.1 to A 58.1 – KE ILOut 136.6 to A 60.6 – KE ILOut 139.4 to A 63.4
– KE ILOut 134.2 to A 58.2 – KE ILOut 136.7 to A 60.7 – KE ILOut 139.5 to A 63.5
– KE ILOut 134.3 to A 58.3 – KE ILOut 137.0 to A 61.0 – KE ILOut 139.6 to A 63.6
– KE ILOut 134.4 to A 58.4 – KE ILOut 137.1 to A 61.1 – KE ILOut 139.7 to A 63.7
Table 6–161: General bit signals, cell level: Addresses 0-1
Signal Data type Address Signal name/description
FC_En Bool %I0.0 Tightening cell enabled
FC_ResetFault Bool %I0.1 Tightening cell reset fault
KE_ResetFault Bool %I0.2 Communication unit reset fault
StartReport Bool %I0.3 Start report
InPos Bool %I0.4 In position
ChnErrAck Bool %I0.5 Channel system error accepted by PLC
R_SRS_A7 Bool %I0.6 Reserve
R_SRS_A8 Bool %I0.7 Reserve
R_SRS_A9 Bool %I1.0 Reserve
R_SRS_A10 Bool %I1.1 Reserve
R_SRS_A11 Bool %I1.2 Reserve
R_SRS_A12 Bool %I1.3 Reserve
R_SRS_A13 Bool %I1.4 Reserve
R_SRS_A14 Bool %I1.5 Reserve
R_SRS_A15 Bool %I1.6 Reserve
R_SRS_A16 Bool %I1.7 Reserve