Bosch Rexroth Sytronix FcP 5020 Скачать руководство пользователя страница 54

Страница: 54 / 88

7.10.5 Pressure and Flow Command Limit

Code

Name

Setting range

Default

Min.

Attri.

F4.00 Protection function configura-

tion word

0...15
Bit0: Pressure sensor failure (PSF)
Bit1: Actual pressure monitoring
Bit2: p/Q max. command limit
Bit3: Oil changing detection

Run

F4.21 Minimum pressure command

limit

0.0...[F4.22] bar

5.0

0.1

Stop

F4.22 Maximum pressure command

limit

[F4.21]...1,000.0 bar

250.0

0.1

Stop

F4.23 Minimum flow command limit 0...[F4.24] rpm

200

Stop

F4.24 Maximum flow command limit [F4.23]...5,000 rpm

3,000

Stop

Tab. 7-23: Parameter list of pressure and flow command limit

The minimum pressure and flow command limitation (F4.21 and F4.23) works all

the time, independently to any control bit. That means if the setting pressure or

flow command is lower than [F4.21] or [F4.23], it will be limited to [F4.21] or

[F4.23] without any error / warning message.
The maximum pressure and flow command limitation can be activated via bit2 of

F4.00. This function will check whether the pressure or flow command given by

customer exceeds the limitation set in [F4.22] and [F4.24]. If a given command

exceeds its limitation, the effective command value will be limited to the maxi-

mum limit, and a warning signal will be raised.

Bosch Rexroth AG
Block Diagram of Main Functions

FcP 5020

50/83

DOK-RCON03-FCP5020****-QU04-EN-P

Содержание Rexroth Sytronix FcP 5020

























































































Результаты поиска

Содержание Rexroth Sytronix FcP 5020

Отзывы:

Похожие инструкции для Rexroth Sytronix FcP 5020

Бренды по названию

Популярные бренды

Bosch Rexroth Sytronix FcP 5020, Быстрый старт

Результаты поиска

Содержание Rexroth Sytronix FcP 5020

Отзывы:

Похожие инструкции для Rexroth Sytronix FcP 5020

Бренды по названию

Популярные бренды