Bosch Rexroth M SED 10 XN Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 48

background image

32/48 Commissioning

Bosch Rexroth AG

, M-.SED 10...XN..., RE 22045-XN-B/05.17

8 Commissioning

wARnInG

Faulty assembly!

If the valve is not correctly mounted, persons might be injured or the product or
system could be damaged when commissioning the valve.

▶

Only commission your system when all hydraulic connections and the valve have
been completely and properly mounted according to the specifications.

▶

Look out for defective sealing points and exchange defective seal rings
immediately.

▶

Wear personal protective equipment during the initial commissioning.

▶

The solenoid coil may only be commissioned if mounted to the valve including
pole tube and mounting nut and if the protective earthing conductor and the
connection for potential equalization conductor are connected.

Inadmissibly high operating pressure!

In hydraulic applications with different area ratios, the hydraulic pressure is
increased and may - in case of incorrect design - lead to an exceedance of the
maximum admissible operating pressure. Thus, the valve may burst or the closing
elements may fly around and cause serious injuries.

▶

Ensure before the commissioning of the hydraulic system that the maximum
admissible pressure of the hydraulic valve in the system is not exceeded by
no means.

▶

Ensure that in your system, the maximum admissible operating pressure is
secured by means of a pressure limitation element.

Damage to persons and property!

Commissioning of the valve requires basic hydraulic and electrical knowledge.

▶

Only qualified personnel (see chapter 2.4 "Qualification of personnel") is
authorized to commission the valve.

NOTICE

Risk of short-circuit!

Condensed water may form inside the electrical connection and cause
a short-circuit!

▶

Allow the valve to acclimatize for some hours prior to commissioning as the
electronics might be damaged by the generation of condensed water.

«
...
30
31
32
33
34
...
»

Содержание Rexroth M SED 10 XN Series

















































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth M SED 10 XN Series

Бренд: Samson Страницы: 78

Бренд: Rachio Страницы: 16

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 20

Бренд: NEC Страницы: 146

Бренд: Value Point Страницы: 7

Бренд: Unitech Страницы: 11

Бренд: B meters Страницы: 10

Бренд: janitza Страницы: 58

Бренд: Balboa Страницы: 74

Бренд: Cadac Страницы: 4

Бренд: Eaton Страницы: 96

Бренд: RADEMACHER Страницы: 68

Бренд: Dantel Страницы: 6

GAMMA VERSUS Series

Бренд: JCM Страницы: 111

767-4804/000-800

Бренд: WAGO Страницы: 80

Bell & Gossett Technologic PPS

Бренд: Xylem Страницы: 20

Бренд: Toro Страницы: 2

Optidrive Elevator

Бренд: Invertek Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды