manualshive.com logo in svg

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 216 / 304

Поделиться
Скачать
Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 216

●

IP address:
The IP address and the onboard Ethernet address entered in the network

configuration are displayed.

The middle section displays the following:
●

Status information:
The status information of the control is displayed via red and green LEDs

(see 

chapter 10.6.2  "Status Information" on page 214

).

●

NC:
In this section, the NC information is displayed (see 

chapter 10.6.3  "Re‐

starting NC" on page 214

).

●

PLC:
In  this  section,  the  PLC  information  is  displayed  (see 

chapter  10.6.4 

"Starting/Stopping the PLC" on page 215

).

The lower section is split in two:
●

The results of the last control restart executed with this application are

displayed on the left (see 

chapter 10.6.5  "Saving Details" on page 215

).

●

The device information is displayed on the right.

10.6.2 

Status Information

The status information of the control is displayed using red and green LEDs:
●

TCP/IP
green LED = Data exchange is active
green LED (not filled) = No data exchange between interface and control

●

Fieldbus
green LED = Fieldbus function ok
red LED = Problem with fieldbus

●

Backup battery
green LED = Correct buffer battery state
red LED = Buffer battery discharged or buffer battery not available

10.6.3 

Restarting NC

The NC display in the middle section is provided with the following:
●

NC status field:
This field visualized the current NC status which is displayed in color and

short  form.  The  used  abbreviations  are  described  in 

chapter  10.6.7 

"Startup Configuration" on page 216

. This field is flashing during control

startup.

●

Info field with detailed status description:
The abbreviations in the status field are explained in this field.

Use <F2> to execute an NC restart. The F-key opens the following dialog. In

this dialog, the startup mode 

chapter 10.6.7  "Startup Configuration" on page

216

 can be specified for a restart.

Bosch Rexroth AG

 DOK-MTX***-NC*OP***V11-AP01-EN-P

 Rexroth IndraMotion MTX 11VRS Standard NC Operation

214/301

Diagnostics

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Отзывы:

Нет отзывов