Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 152

Страница: 152 / 304

A zero offset table with the selected configuration is created and is opened in

the zero offset editor.

Using Table Templates

Proceed as follows to use any zero offset table as a template:
1.

Dialog New (see

fig. 7-28 " Dialog to create a new zero offset table" on

page 149

) as described above.

If necessary, enter a new name for the zero offset table.

In the dialog New select the field "Template".
The entry field for the name of the template (default: "ZO1.zot") is activa‐

ted. If the default "ZO1.zot" is not used, a name with the path information

of another zero offset table can be entered here. If a table name is entered

without path information, the template is sought in the path "/database".

Acknowledge the entry by pressing the "Ok" button.

The new table is opened in the zero offset editor. The number of correction

pages and correction values is adopted from the given template.

Functions on the Main Level of the Zero Offset Editor

<F2 Add correction page> can be used to add new zero point data sets to the

table. New data sets are attached to the end of the table.

Zero point data sets are assigned running numbers (correction

page 1-5).

<F3 Remove correction page

<F3 Remove correction page> removes the last zero point data set.

Additive Value Entry

"Additive value entry" can be used to enter correction values that are to be

added to the existing value (see

chapter "Value Entry" on page 143

Menu Tools

<F2 Add axis

<F2 Add axis> adds a new axis at any location.

Fig.7-29:

Dialog to add a new axis

Select the axis in front of which the new axis is to be inserted (i.e. any cell

of the axis has to be selected).

Press <F2 Add axis>.
The selected axis is highlighted. The dialog Insert axis (refer to

fig. 7-29

" Dialog to add a new axis" on page 150

) is opened.

Enter the name of the axis (maximum of 8 characters).

Select axis type "Linear axis" or "Rotary axis".

If necessary, specify a special channel ("0" for all)

If the axis is to be attached, "Attach axis" also has to be selected.

Complete the entry by pressing the "Ok" button.

The new axis is added according to the settings.

Bosch Rexroth AG

DOK-MTX***-NC*OP***V11-AP01-EN-P

Rexroth IndraMotion MTX 11VRS Standard NC Operation

150/301

Programming

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 152 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: