Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 61

Страница: 61 / 422

CNCA is the Chinese authority responsible for certification guidelines. When

a product is imported in China, the certification will be checked at customs

using the entries in a database. Three criteria are typically critical for

certification being required:
1.

Customs tariff number (HS code) according to CNCA document

"Application Scope for Compulsory Certification of Products acc. first

Catalogue".

Area of application according to CNCA document "Application Scope for

Compulsory Certification of Products acc. first Catalogue".

For the IEC product standard used, a corresponding Chinese

GB‑standard must exist.

For the drive components by Rexroth described in this documentation,

certification is currently not required, so they are not CCC certified. Negative

certifications will not be issued.

4.2

Transport and storage

4.2.1

Transporting the components

Ambient and operating conditions for transport

Description

Symbol

Unit

Value

Temperature range

a_tran

°C

-20 … +70

Relative humidity

5 … 95

Absolute humidity

g/m

1 … 60

Climatic category (IEC 721)

2K3

Moisture condensation

Not allowed

Icing

Not allowed

Tab. 4-4:

Ambient and operating conditions for transport

4.2.2

Storing the components

Risk of damage to the

KCU drive connection

box from long-term storage!

NOTICE

The KCU drive connection box contains electrolytic capacitors which may

deteriorate during storage. When storing the KCU drive connection box for a

longer period of time, run it once a year for at least 1 hour at 24 V control

voltage U

Risk of damage to the

KMV supply unit from

long-term storage!

NOTICE

The KMV supply unit contains electrolytic capacitors which may deteriorate

during storage. When storing the KMV supply unit for a longer period of time,

run it once a year for at least 1 hour at mains voltage U

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

47/407

General data and specifications

R911335703_Edition 04 Bosch Rexroth AG

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды