Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 372 | Manualshive

Страница: 372 / 422

background image

11.4.3

Deactivating and Dismounting the Drive

Deactivation

In the case of malfunction, maintenance measures or to deactivate the

motors, proceed as follows:

1. Observe the instructions contained in the machine documentation.
2. Use the machine-side control commands to bring the drive to a

controlled standstill.

3. Switch off the power voltage and control voltage of the controller.
4. Switch off the main switch of the machine.
5. Secure the machine against accidental movements and against

unauthorized operation.

6. Wait to allow the electric systems to discharge and then disconnect all

electrical connections.

7. Before dismounting them, secure the motor and, if necessary, the fan

unit against falling or movements, before unfastening the mechanical

connections.

Dismounting

Lethal injury caused by errors when

controlling motors and working at moving

parts!

WARNING

●

Do not work at running or unsecured installations.

●

Before starting to dismount, secure the machine against accidental

movements and unauthorized operation.

●

Before dismounting them, secure the motor and the supply lines unit

against falling or movements, before unfastening the mechanical

connections.

Burns caused by hot surfaces with

temperatures of more than 100 °C!

CAUTION

●

Before beginning to work, let the motors cool down. The thermal time

constant specified in the Technical Data is a measure for the time

required for cooling down. Cooling down can require up to 140 minutes!

●

Do not work at hot surfaces.

●

Wear safety gloves.

1. Observe the instructions contained in the machine documentation.
2. Observe the Safety Instructions and carry out all steps according to the

instructions for "

".

3. Before dismounting them, secure the motor and the supply lines unit

against falling or movements, before unfastening the mechanical

connections.

4. Dismount the motor from the machine.
5. Store the motor appropriately.

358/407

Commissioning, operation, diagnostics and maintenance

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

«
...
370
371
372
373
374
...
»

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренд: S&C Страницы: 40

Бренд: S&C Страницы: 34

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 26

Бренд: NAiS Страницы: 199

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 179

Бренд: Panasonic Страницы: 23

Бренд: Panasonic Страницы: 30

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 20

INDUSTRY PAN9028

Бренд: Panasonic Страницы: 34

Бренд: TAC Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды