Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 114

Страница: 114 / 422

Braking resistor

Integrated braking resistor data

Description

Symbol

Unit

KMV03.1R-

A05K0-P-D7-

ET-NNNN

KMV03.1R-

B0007-P-D7-

ET-NNNN

KMV03.1R-

I01K5-P-D7-

ET-NNNN

KMV03.1R-

W06K0-P-D7-

ET-NNNN

Braking resistor continuous power

0.15

Braking resistor peak power

12.00

Nominal braking resistance

DC_Bleede

ohm

Braking

resistor

switch-on

threshold - independent of mains
voltage

R_DC_On_f

820

Regenerative power to be

absorbed

R_max

kWs

7.50

Cooling of integrated braking

resistor

Heat sink

Base plate (Coldplate)

Heat sink

Latest amendment: 2019-08-08

Factory setting

Tab. 5-15:

KMV - Integrated braking resistor data

100/407

Technical data of the components

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды