Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 54

Страница: 54 / 344

Requirements on the Encoder of the Third-Party Motor
Motor Encoder of Asynchronous Third-Party Motor

Asynchronous motors can also be controlled by Rexroth IndraDrive Cs con‐

trollers in "open-loop" operation (without motor encoder). In "closed-loop" op‐

eration (with motor encoder), a relative measuring system is sufficient for

asynchronous motors.

Motor Encoder of Synchronous Third-Party Motor

For fail-safe drives with synchronous third-party motors at

Rexroth IndraDrive Cs controllers, the following possible combinations or re‐

strictions have to be taken into account when selecting the measuring sys‐

tem:

Drive range

Motor measuring system

Synchronous third-party

motor

Rexroth IndraDrive Cs

Absolute

■

Relative

□

■

Advantageous combination

□

Combination is possible (restrictions specific to application),

commissioning may be more complicated!

Tab. 4-10:

Possible Combinations of Synchronous Third-Party Motor and Motor

Measuring System

The drive controller can evaluate measuring systems as motor

encoder when they are contained in "P-0-0074, Encoder type 1

(motor encoder)".
For information on absolute and relative measuring systems, see

section "Measuring Systems" of firmware documentation!

Motor Encoder Resolver - Notes on Selection

Resolvers must first be checked as to whether they are suited as motor en‐

coders. To check whether they can be evaluated by the drive controllers, the

following resolver data are required:
●

Data of resolver system to be compared must be available at 8 kHz

●

Ratio

●

Current consumption

●

DC resistance of stator

●

Number of poles

●

Phase shift

By means of the resolver data, check whether the supply voltage of the en‐

coder interface and the signal levels of the encoder tracks are sufficient.

Notes on Selection and Commissioning
Selecting the Controller as Regards Continuous Current

The drive controller required for the respective motor is determined by com‐

paring the motor data to the device data.

Bosch Rexroth AG

DOK-INDRV*-HCS01******-PR05-EN-P

52/341

Rexroth IndraDrive CsDrive Systems with HCS01

Combining the individual components

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды