Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 136

Страница: 136 / 344

X5, Motor Connection

Important Notes

Lethal electric shock by live parts with more

than 50 V!

WARNING

Exclusively operate the device
●

with plugged on connectors (even if there haven't been any lines con‐

nected to the connectors) and

●

with connected equipment grounding conductor!

Risk of damage to the device!

NOTICE

Provide strain relief for the terminal connectors of the device in the control

cabinet.

Notes on Installation

The equipment grounding conductor is connected directly to the device and

not via the connection point X5.
The indicated connection cross sections are the cross sections which can be

connected. Dimension the required cross section of the connection lines ac‐

cording to the occurring current load.

●

For optimum shield contact of the motor power cable, use

the supplied accessory

HAS09

●

For the connection between drive controller and motor, use

our ready-made motor power cables, where possible.

●

When using NFD03.1 mains filters, the maximum allowed

conductor cross section is limited to 4 mm

Bosch Rexroth AG

DOK-INDRV*-HCS01******-PR05-EN-P

134/341

Rexroth IndraDrive CsDrive Systems with HCS01

Mounting and installation

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды