Bosch Rexroth IndraControl XFE 01.1 Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 36

background image

14 / 36

IndraControl XFE 01.1

Bosch Rexroth AG

R911345570, Edition 06

8.5

Marine and offshore certification (XFE01.1-FB-03, XFE01.1-

FB-20)

The extension modules XFE01.1-FB-03, XFE01.1-FB-20 are suitable for the use in marine and offshore

applications and were approved by the following certification organizations:

•

DNV Det Norske Veritas, Germanischer Lloyd DCTC_30826-001

•

ABS American Bureau of Shipping DCTC_30826-002

•

RINA Registro Italiano Navale DCTC_30826-003

•

LR Lloyd's Register DCTC_30826-004

•

BV Bureau Veritas DCTC_30826-005

•

BSH Bundesamt für Seeschifffahrt und Hydrographie DCTC 30826-006

The certificates are stored in our Internet portal. Go to our Internet site

www.boschrex-

and select the country-specific section. To search for certificates, enter one of the

above mentioned certificate numbers (DCTC_xxxxx_xxx) into the search field in the upper

right.

9

Interfaces of the XFE modules

9

4

5

2

3

1

1

7

8

6

Fig. 4: Interfaces of the extension modules

«
...
12
13
14
15
16
...
»

Содержание Rexroth IndraControl XFE 01.1 Series





































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth IndraControl XFE 01.1 Series

Бренд: Ohsung Electronics Страницы: 18

Бренд: Samson Страницы: 40

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: Nedap Страницы: 20

Бренд: u-blox Страницы: 28

Бренд: Vaillant Страницы: 27

Бренд: Vaillant Страницы: 36

Бренд: Vaillant Страницы: 28

Бренд: Vaillant Страницы: 92

Бренд: RadioMaster Страницы: 49

SUPERREMOTE UR19A

Бренд: X10 Страницы: 3

Бренд: Xantech Страницы: 102

Бренд: Xantech Страницы: 17

Бренд: X10 Страницы: 2

Бренд: SOMFY Страницы: 112

Бренд: Osaka Страницы: 12

Бренд: Nanjing Putian Datang Information Electronics Co., Ltd. Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды