Bosch REXROTH IndraControl VAM 12.1 Скачать руководство пользователя страница 43

Страница: 43 / 96

5.6.2

Mounting Cut-Out

To mount the control panel, proceed as follows:

1. Create a mounting cut-out with 6 holes, cross-section 4.5 mm according

fig. 5-11 "Mounting dimensions VAM 12.1" on page 41

and

fig. 5-12

"Mounting dimensions VAM 42.1" on page 42

2. Insert the control panel from the front into the cut-out. Then insert the

mounting bolts M4 into the drilled holes.

3. Fasten the control panel by screwing the nuts at the rear side of the

mounting bolts.

Damage to the mechanics due to incorrect

tightening torque.

NOTICE

The tightening torque for M4 nuts (1.4 Nm) must not be exceeded.

5.6.3

Mounting Dimensions VAM 12.1

Mounting cut-out

215 x 324

225

240

7.5

167.5

350

7.5

Hole for threaded bolts

Fig.5-11:

Mounting dimensions VAM 12.1

DOK-SUPPL*-VAM*XX.1***-PR02-EN-P
Rexroth IndraControl VAM 12.1/42.1 Machine Control Panels

Bosch Rexroth AG

41/93

Dimensions and Installation

Содержание REXROTH IndraControl VAM 12.1

































































































Результаты поиска

Содержание REXROTH IndraControl VAM 12.1

Отзывы:

Похожие инструкции для REXROTH IndraControl VAM 12.1

Бренды по названию

Популярные бренды

Bosch REXROTH IndraControl VAM 12.1, Руководство по планированию проекта

Результаты поиска

Содержание REXROTH IndraControl VAM 12.1

Отзывы:

Похожие инструкции для REXROTH IndraControl VAM 12.1

Бренды по названию

Популярные бренды