Bosch Rexroth IndraControl S20 страница 68 Скачать руководство пользователя

Страница: 68 / 88

IDN

Sercos parameter number

Tab. 13-1:

Sercos parameters

13.2

CSos parameters (safe configuration)

CSos parameters are connection parameters within the safe configuration.

The values formatted in bold

tab. 13-2 "Overview on the CSos pa‐

rameters of the module" on page 66

are specified by the system

and cannot be changed manually.

CSos parameters

Default val‐

Description

Vendor ID

287

Vendor ID of Bosch Rexroth AG

Device Type

1027

Safety discrete I/O

Product Code

Specified by Bosch Rexroth AG

Major Revision

Major revision of the module

Minor Revision

Minor revision of the module

Connection name

Output

Name of the connection instance

Safety configuration

CRC (SCCRC)

0xB390FB

The CRC calculated in the safe parameterization

is entered here. Default value results from the de‐

fault parameterization.

Safety Configura‐

tion Time Stamp

(SCTS)

0x6000000

Specified value

Safety Network

Number (SNN)

0x6000000

SNN set at the DIP 0x600000000

Safety Device ID

(SDID)

SDID set at the DIP switch

Format Type

Telegram format:
1 base format
2 extended format

Network Time Ex‐

pectation (NTE)

This period in ms is monitored and guarantees

that the process data is not older than the NTE.

Timeout Multiplier

Number of telegrams that can be lost before a

connection error is reported.

Max. fault number

Number of incorrect packages per hour before a

connection is closed.

Timeout

1000

Period in ms that is waited for a connection to be

established.

Device Info

SDDML-

V3.0..

Name of the SDDML file used

Creator Info

Bosch

Rexroth

Generator of SDDML file

Tab. 13-2:

Overview on the CSos parameters of the module

Bosch Rexroth AG

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

66/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

CSos parameters and device parameters

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды