Bosch Rexroth IndraControl L10 Скачать руководство пользователя страница 27

Страница: 27 / 62

Display and Operating Components

6.1

General Information

The web-based "IndraControl Service Tool" is integrated in the

IndraControl L10 for the display and the operation. The control can be accessed

with a web browser via an Ethernet interface. The IP address is set to

192.168.1.10 when shipped. Further information under /1/.
The reset button and the status LED are located on the front of the

IndraControl L10.

6.2

Reset Button and Status LED

The Reset button and the multicolor LED are located on the left side of the

device front.

Fig.6-1:

Recessed reset button and status LED

Pressing the reset button will abort processing of a running pro‐

gram.

The reset button can only be pressed using a tool, for instance with the tip of a

pencil.
Three different actions can be activated using the Reset button:
1.

Short pressing of the reset button during the operation resets the complete

assembly and forces a restart the without a switch off of the supply vol‐

tages.

Long pressing of the reset button during the operation resets the complete

assembly and forces a restart without a switch off of the supply voltages.

Additionally, the IP address is reset to the delivery status (192.168.1.10).

Therefore, the reset button is to be pressed till the booting phase ends.

The period of the booting phase is indicated with an orange status light

emitting diode.

If the reset button is pressed during the switch-on voltage of the power

supply, the existing boot project is deleted.

Project Planning Manual | Rexroth IndraControl L10

Electric Drives

and Controls

| Bosch Rexroth AG

21/54

Display and Operating Components

Reset button

Courtesy

CMA/Flodyne/Hydradyne

▪

Motion

Control

▪

Hydraulic

▪

Pneumatic

▪

Electrical

▪

Mechanical

▪

(800)

426-5480

▪

www.cmafh.com

Содержание Rexroth IndraControl L10































































Результаты поиска

Содержание Rexroth IndraControl L10

Отзывы:

Похожие инструкции для Rexroth IndraControl L10

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl L10, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraControl L10

Отзывы:

Похожие инструкции для Rexroth IndraControl L10

Бренды по названию

Популярные бренды