manualshive.com logo in svg

Bosch Rexroth Hagglunds CA 10, Руководство по установке и обслуживанию

Поделиться
Скачать
Bosch Rexroth Hagglunds CA 10 Скачать руководство пользователя страница 17

16/52 

Transport and storage

RE 15354-WA/04.2015, Installation and maintenance manual, Hägglunds CA 10 - CA 40, 

Bosch Rexroth Mellansel AB

6 

Transport and storage

6.1  Product transport

6.1.1  lifting methods

 DANGER

Danger while transporting or lifting Hägglunds motors due to heavy weight!

Danger to life, risk of injury or serious injuries and risk of damage to equipment! 

 

▶

Make sure that lifting device is correctly installed.

 

▶

Do not stand under suspended load.

Danger if using wrong lifting eyes!

Danger to life, risk of injury or serious injuries and risk of damage to equipment! 

 

▶

Make sure the correct lifting eye is used and tightened close to the mating 
surface, see 

Fig. 4: Lifting eyes at motor

: 

Center of gravity

Fig. 3: Center of gravity

Table 4: Center of gravity

Motor type

Measure A (mm)

CA 10

99

CA 20

118

CA 30

137

CA 40

164

DD00070605

Fig. 4: lifting eyes at motor

DD00070606

lifting eyes

lifting eyes

A

Содержание Rexroth Hagglunds CA 10






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды