manualshive.com logo in svg

Bosch R901234567, Руководство по эксплуатации

Поделиться
Скачать
Bosch R901234567 Скачать руководство пользователя страница 43

 

Technical data 43/48

 

RE29583-XL-B/09.20, 4WS2EM 10...XL..., 

Bosch Rexroth AG

  

The valve is not sensitive to faults as long as the specified application conditions are 
complied with, in particular the oil quality and the operating temperature.

Table 17: Fault table

Error

Possible cause(s)

Remedy

Valve does not react 
to control

Electrical connection 
interrupted, 
no current continuity
•  Cable break

Replace the connection cable

•  Mating connector not 

connected

Connect the mating connector

•  Connector without contact

Remove valve and have it repaired

•  Valve-internal cable break

Remove valve and have it repaired

No pilot oil pressure available
•  No pressure at P

Ensure the pilot oil supply

•  Filter blocked

Exchange filter element and check system 
for contamination

•  Orifice blocked

Remove valve and have it repaired

Zero flow too high

•  Control edges worn

Remove valve and have it repaired

Bad dynamic 
behavior

•  Filter contaminated

Exchange filter element and check system 
for contamination

•  Orifice contaminated

Remove valve and have it repaired

Instable zero point

•  Control spool friction due to 

contamination

Remove valve and have it repaired

Hysteresis

•  Control spool friction due to 

contamination

Remove valve and have it repaired

Large zero point 
deviation

•  Orifice contaminated

Remove valve and have it repaired

External leakage

Seal defective
•  Seal at the connection 

surface is defective

Remove the valve and replace the seals

•  Seal at filter screw is 

defective

Disassemble the filter screw and replace 
the seal

•  Other leakage

Remove valve and replace it with 
a new one

Following faults due to contamination, in addition to the repair, it is essential 
to check the oil quality and improve it, if necessary, by suitable measures such as 
flushing or the additional installation of filters.

15 Technical data

For the technical data of your valve please refer to 

"Data sheet 29583-XL"

.

Fault table

Содержание R901234567

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды