B: die Bypass-Schrauben bis zum korrekten Gasaustritt an den
Brennern lockern: stellen Sie sicher, dass der Brenner bei einer
Umstellung des Bedienknebels von der höchsten auf die nied-
rigste Stufe nicht ausgeht und nicht zurückschlägt.
C: die Bypass-Schrauben müssen von einem autorisierten
Fachmann ausgetauscht werden.
D: nehmen Sie keine Veränderungen an den Bypass-Schrau-
ben vor.
Um die Dichtheit zu gewährleisten, müssen
alle
Knebeldichtun-
gen eingesetzt werden. Die Dichtungen sind für den fehlerfreien
Betrieb des Geräts unerlässlich, da sie das Eindringen von Flüs-
sigkeiten und Schmutz ins Geräteinnere verhindern.
Stecken Sie die Bedienknebel wieder auf.
Bauen Sie niemals die Achse des Gashahns aus (Abb. 8). Bei
einer Störung den kompletten Gashahn ersetzen.
Achtung!
Bringen Sie den Aufkleber mit der umgestellten Gasart in der
Nähe des Typenschildes an.
en
Ú
Installation instructions
Safety precautions
Read the appliance instructions before installing and using.
The graphics in these Assembly instructions are given as a
guide only.
The manufacturer is exempt from all liability if this manual's
requirements are not complied with.
All operations relating to installation, regulation and
conversion to other gas types must be carried out by an
authorised installation engineer, respecting all applicable
regulations, standards and the specifications of the local gas
and electricity providers.
You are recommended to contact the Technical Assistance
Service to convert to another gas type.
Before you begin, turn off the appliance's electricity and gas
supply.
This appliance has been designed for home use only, not for
commercial or professional use. This appliance cannot be
installed on yachts or in caravans. The warranty will only be valid
if the appliance is used for the purpose for which it was
designed.
Before installing, check that local distribution conditions (gas
type and pressure) and the appliance's adjustment are
compatible (see table I). The appliance's adjustment conditions
are written on the label or the specifications plate.
This appliance can only be installed in a well-ventilated place in
accordance with existing regulations and ventilation
specifications. The appliance must not be connected to a
combustion product removal device.
The supply cable must be attached to the unit to prevent it from
touching hot parts of the oven or hob.
Appliances with electrical supply must be earthed.
Do not tamper with the appliance's interior. If necessary, call our
Technical Assistance Service.
Before installing
This appliance is class 3 type, according to the EN 30-1-1
regulation for gas appliances: built-in appliance.
The units next to the appliance must be made of non-flammable
materials. The laminated covering and glue for adhering it must
be heat resistant.
This appliance cannot be installed above fridges, washing
machines, dishwashers or similar.
An oven must have forced ventilation to install a hob above it.
Check the dimensions of the oven in the installation manual.
If an extractor fan is installed, you must follow the installation
manual's instructions, always keeping a minimum distance of
650 mm to the hob.
Preparation of the kitchen unit (fig. 1-2)
Make an appropriate size cut in the work surface.
If the hob is electric or mixed (gas and electricity) and there is
no oven below, place a non-flammable separator (e.g. metal or
plywood) 10 mm from the bottom of the hob. This will prevent
access to the base of the hob.If the hob is gas, it is
recommendable to place the separator at the same distance.
On wood work surfaces, varnish the cutting surfaces with a
special glue. This protects them from moisture which could
collect under the work surface.
Installation of appliance (fig. 3)
Note:
Wear protective gloves to fit the hob.
The clips and adhesive seal (underside of the hob) are factory-
fitted: Do not remove these under any circumstances: The
adhesive seal prevents water seepage.
In order to fit the appliance into the kitchen unit, first place the
hob in the correct position then loosen each of the clips so that
they all turn freely (it is not necessary to completely undo them).
Insert and centre the hob.
Press the sides of the hob until it is supported around its entire
perimeter.
Turn the clips and tighten them fully. Fig. 3.
Removal of hob
Turn off the appliance's electricity and gas supply.
Unscrew the clips and proceed in the reverse order to
installation.
Gas connection (fig. 4)
The gas connection must be located in a position where the
stop tap is accessible.
The end of the inlet connection point of the gas hob has a 1/2”
thread (20.955 mm) that allows for:
■
A fixed connection.
■
Connection using a flexible pipe (L min. 1 m - max. 3 m).
You must prevent the pipe from coming into contact with
moving parts of the kitchen unit (for example, a drawer) and
prevent access to any spaces which might become obstructed.
:
Danger of leaks!
If any connection is handled, check the seal.
The manufacturer is not liable for any connection leaking, after
being handled.
Electric connection (fig. 5)
Check that the voltage and power of the appliance are
compatible with the electrical installation.
The hobs are supplied with a power cable with or without a wall
socket plug.
Appliances with plugs must only be connected to sockets that
have earth wires correctly installed.
Provide an omnipolar cut-off switch with a minimum contact
opening of 3 mm (except for plug connections, if the user has
access to it).
This appliance is type “Y”: the supply cable can only be
changed by the Technical Assistance Service and not the user.
The cable type and minimum cross-section must be respected.
Changing the gas type
If the country's regulations allow, this appliance can be adapted
to other types of gas (see specifications plate). The components
required for this are in the transformation kit supplied
(depending on the model) or are available from our Technical
Assistance Service. The following steps should be taken:
A) Changing the nozzles (fig. 6):
1.
Remove the pan supports, burner caps and diffusers.
2.
Change the nozzles using the spanner code 424699 provided
by our Technical Assistance Service, see table II, taking
special care to ensure that the nozzle does not fall when it is
removed from or fitted to the burner.
Ensure that it is completely tightened in order to guarantee the
seal.
Primary air adjustment is not necessary with these burners.
3.
Position the diffusers and burner caps on the corresponding
rings. The pan supports must also be positioned correctly.
B) Adjusting the taps
1.
Set the control knobs to minimum.
2.
Remove the control knobs from the taps. Fig. 7.
It has a flexible rubber valve reinforcing ring. Simply press on
this seal with the tip of a screwdriver to allow access to the tap
adjusting screw.
Never remove the valve reinforcing ring.
3.
Adjust the minimum ring setting by turning the by-pass screw
using a flat head screwdriver.
Depending on the gas to which your appliance is going to be
adapted, see table III, carry out the corresponding action:
A: firmly tighten the by-pass screws.
